Grizzly G0733 owner manual WZbdjciZYdciZZVYhidX`hejgXZciZg#, Ldg`eZXZ 8ZciZg

2. BV`ZVXZciZgbVg`Wnjh^c\VlddYbVaaZi VcYiVee^c\i]Zed^cid[i]ZhejgXZciZg^cid i]ZXZciZgd[i]Zldg`e^ZXZdcWdi]ZcYh#

3. Jh^c\V&¿)Yg^aaW^i!Yg^aaV&¿)YZZe]daZVii]Z

XZciZg bVg` dc i]Z ZcY d[ i]Z ldg`e^ZXZ id

WZbdjciZYdci]Z]ZVYhidX`hejgXZciZg#

4. Id ]Zae ZbWZY i]Z hejg XZciZg ^cid i]Z ldg`e^ZXZ! Xji &¿- YZZe hVl `Zg[h ^c i]Z ]ZVYhidX` ZcY d[ i]Z ldg`e^ZXZ Vadc\ i]Z Y^V\dcVaa^cZhbVg`ZY^cStep 1#

5. >[ndjgldg`e^ZXZ^hdkZg'm'!Xjii]ZXdg" cZgh d[[ i]Z ldg`e^ZXZ aZc\i]l^hZ id bV`Z ijgc^c\hV[ZgVcYZVh^ZghZZFigure 37#

Ldg`e^ZXZ

8ZciZg

Figure 37.8dgcZghd[ldg`e^ZXZgZbdkZY#

6. 9g^kZ i]Z hejg XZciZg ^cid i]Z ZcY XZciZg bVg`d[i]Zldg`e^ZXZl^i]VlddYbVaaZiid ZbWZY ^i Vi aZVhi &¿) ^cid i]Z ldg`e^ZXZ! Vh h]dlc^cFigure 38#

&$)

Figure 38.HejgXZciZgegdeZganZbWZYYZY#

"'-"

7. L^i] i]Z ldg`e^ZXZ hi^aa ViiVX]ZY! ^chZgi i]Z hejgXZciZg^cidi]Z]ZVYhidX`he^cYaZgZ[Zg id Installing/Removing Headstock Center dcPage 23 [dgVYY^i^dcVa^chigjXi^dch#

Note: Use the tool rest to support the opposite end of the workpiece so that the workpiece and spur center do not separate during installation.

8. >chiVaa i]Z a^kZ XZciZg ^cid i]Z iV^ahidX` fj^aa VcY i^\]iZc i]Z fj^aa adX` ]VcYaZ id adX` i]Z fj^aa ^c edh^i^dc gZ[Zg id Page 24 [dg VYY^" i^dcVa^chigjXi^dch#

9. Ha^YZ i]Z iV^ahidX` idlVgY i]Z ldg`e^ZXZ jci^a i]Z ed^ci d[ i]Z a^kZ XZciZg idjX]Zh i]Z ldg`e^ZXZXZciZgbVg`!i]ZcadX`i]ZiV^ahidX` ^ci]^hedh^i^dc#

10. AddhZc i]Z fj^aa adX` ]VcYaZ VcY gdiViZ i]Z iV^ahidX` ]VcYl]ZZa id ejh] i]Z a^kZ XZciZg ^cidi]Zldg`e^ZXZViaZVhiV&¿)#

Do not press the workpiece too firmly with the tailstock or the bearings will bind and overheat. Do not adjust the tailstock too loosely or the workpiece will spin off the lathe. Use good judgment and care, other- wise, serious personal injury could result from the workpiece being ejected at high speeds.

11. EgdeZganVY_jhii]ZiddagZhiidi]Zldg`e^ZXZ

hZZ Adjusting Tool Rest dc Page 23#

12. 7Z[dgZ WZ\^cc^c\ aVi]Z deZgVi^dc! gdiViZ i]Z ldg`e^ZXZ Wn ]VcY id ZchjgZ i]Vi i]ZgZ ^h hV[ZXaZVgVcXZdcVaah^YZh#

Keep the lathe tool resting on the tool rest the ENTIRE time that it is in contact with workpiece or when preparing to make contact between lathe tool and workpiece. Otherwise, the spinning workpiece could force the lathe tool out of your hands or entangle your hands with the workpiece. Failure to heed this warning could result in serious personal injury.

BdYZa<%,((B[\#H^cXZ&%$&&