NOTE
If the FAN button is pressed again or if no button is pressed for two minutes, the thermostat will exit the configuration mode and return to nor- mal operation. To
While in the configuration mode, the following options are available:
A. ANTICIPATOR -- Value Adjustment
This adjustment controls the sensitivity and cycle rate of the thermostst. Higher numbers decrease the sensitivity and slow the cycle rate. Lower numbers increase the sensitivity and increase the cycle rate. However, a limiting feature will not allow more than 4 equipment cycles per hour, regardless of setting. Values can range from 1 to 3. Factory default setting is 2. This default selection will provide optimum performance in nearly all installations. Try it first. Do not change settings unless there is evidence of need to do so. Unlike conventional anticipators, this setting is not determined by current draw. There is no need to measure, know, or compensate for current.
To Adjust:
a.Enter configuration mode (if not already there).
b.Use UP & DOWN buttons to display A.
c.Press MODE button once to display current value.
d.Use UP & DOWN buttons to move between values.
e.Press MODE buttonto return to A. UP & DOWN buttons now move between option choices A, d, oF or press FAN button to exit configuration mode.
c.Press MODE button once to display offset value.
d.Use UP & DOWN buttons to select a value between
e.Press MODE buttonto return to oF. UP & DOWN buttons now move between option choices; or press FAN button to exit configuration mode.
3.10 CHECK THERMOSTAT OPERATION
3.10.1 Fan Operation (Cool Only)
1.Press FAN button, starting fan operation. FAN an- nunciator turns on; Lo is displayed in the room tem- perature area for 5 seconds indicating Fan Low Speed.
2.Press FAN button, FAN annunciator remains on; Hi is displayed in room temperature area for 5 seconds indicating Fan High Speed.
3.Press FAN button, stopping fan operation. FAN an- nunciator turns off.
3.10.2 Fan Operation (Heat/Cool)
1.Press FAN button, starting low fan (Lo) operation. FAN annunciator turns on.
2.Press FAN button, starting high fan (Hi) operation. FAN annunciator remains on.
3.Press FAN button, stopping fan operation. FAN an- nunciator turns off.
3.10.3 Cooling Operation (Cool Only)
1.Press and release MODE button until COOL is dis- played.
d. Fahrenheit/Celsius Selection
This selection operates the thermostat in either Fahrenheit or Celsius.
To Select:
a.Enter configuration mode (if not already there).
b.Use UP & DOWN buttons to display d.
2.Press DOWN button until LCD readout reads 10 de- grees below room temperature. Cooling and High Fan system should begin to operate within 5 min- utes.
3.10.4 Cooling Operation (Heat/Cool)
1.Press and release MODE button until COOL is dis- played.
c.Press MODE button once to display current selection of F or C.
d.Use UP & DOWN buttons to change between F & C.
e.Press MODE buttonto return to d. UP & DOWN buttons now move between option choices; or press FAN button to exit configuration mode.
oF. Room Temperature Offset Adjust Selection
The selected number is the number of degrees, plus or minus, which will be added to the actual temperature. The numbers can range between
To Select:
a.Enter configuration mode (if not already there).
b.Use UP & DOWN buttons to display oF .
2.Press DOWN button until LCD readout reads 10 de- grees below room temperature. Cooling and High Fan system should begin to operate within 5 min- utes.
3.10.5 Heating Operation (Heat/Cool)
1.Press and release MODE button until HEAT is dis- played.
2.Press UP button until LCD readout reads 10 degrees above room temperature. Heating system should begin to operate within 1 minute.
3.11 CHECK THERMOSTAT OPERATION
3.11.1 Temperature Display
The thermostat will display room temperature until the UP or DOWN button is pressed. The word SET appears when these buttons are pressed and the current set point is displayed. If no buttons are pressed for 5 seconds, the display will change back to show room temperature.