Bosch Power Tools CS20 manual Power Tool Safety Rules, Work Area

Page 2

BM 2610919169 10-03 10/23/03 11:54 AM Page 2

 

Power Tool Safety Rules

 

Read and understand all instructions. Failure to follow all instructions listed

! WARNING

 

below, may result in electric shock, fire and/or serious personal injury.

 

 

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit.

Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust or fumes.

Keep by-standers, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation

eliminates the need for the three wire

grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

Don't expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use

and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while

operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

Keep handles dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece to a

-2-

Image 2
Contents 2610919169 Power Tool Safety Rules Work AreaSafety Rules for Circular Saws ServiceCauses and Operator Prevention Kickback Or Kickback from the workpiece as the saw is restarted Symbols Functional Description and Specifications Circular SawAssembly VARI-TORQUE ClutchInstalling Power Cord FIG. aOperating Instructions Depth AdjustmentBevel Adjustment Cutting Angle CheckCutting MASONRY/METAL SwitchGeneral Cuts Pocket Cuts Cutting Large SheetsMaintenance Accessories Care of BladesSécurité électrique Règles de Sécurité GénéralesAire de travail Sécurité des personnesConsignes de sécurité pour scies circulaires RéparationCauses ET PRÉVENTION, PAR Lopérateur DU Rebond Le plomb provenant des peintures à base de plomb Symboles NOMCapacités maximales Description fonctionnelle et spécificationsScie circulaire Assemblage Embrayage « VARI-TORQUE »Installation du cordon dalimentation LE Système DE RaccordVérification DE L’ANGLE DE Coupe Consignes de fonctionnementRéglage DE LA Profondeur DE Coupe Réglage DE LA Coupe EN BiseauSciage DES Matériaux DE Maçonnerie ET DES Métaux InterrupteurCoupes Régulierès Coupe DE Grandes Feuilles Coupes EN GuichetLa lame Nettoyage ServiceEntretien Et certains AccessoiresCertains Agents Entretien DES LamesSeguridad eléctrica Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad personalNormas de seguridad para sierras circulares ServicioCausas DEL Retroceso Y SU Prevencion POR EL Operador Embrague DE PAR Motor VariableBM 2610919169 10-03 10/23/03 1154 AM Símbolos De Ni-CdDescripción funcional y especificaciones Sierra circularEnsamblaje Embrague DE PAR Motor VariableInstalación del cordón energía EL Sistema DE ConexiónInstrucciones de funcionamiento Ajuste DE InclinaciónCortes Generales Guía DE LíneaGuía DE Interruptor Movimiento libre del protector inferiorCortes DE Bolsillos Corte DE Planchas GrandesMantenimiento LimpiezaAccesorios Cuidado DE LAS HojasBM 2610919169 10-03 10/23/03 1154 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools