Black & Decker BDBS100 instruction manual Adjusting Blade Tension, Tracking the Blade

Page 11

ADJUSTING

BLADE TENSION

Blades of 1/8 in., 1/4 in., and 3/8 in. in width by

59-1/2 in. in length are available for use with your band saw. NOTE: The blade tension must be adjusted to accommodate different blade widths in order to provide proper blade tracking, cutting performance, and blade life.

WARNING: DISCONNECT MACHINE FROM POWER SOURCE.

1.After the desired blade is assembled to the two wheels, turn tension knob (A) Fig. 19, clockwise until spring (B) begins to compress.

2.Turn tension knob (A) Fig. 19, an additional 2-1/2 turns for 1/8 in. wide blades; 3 turns for 1/4 in. wide blades; and 4 turns for 3/8 in. wide blades.

3.A chart (C) Fig. 19, is located at the rear of the band saw. This chart shows blade size, and the minimum radius that can be cut with each size blade.

TRACKING THE BLADE

WARNING: DISCONNECT MACHINE FROM POWER SOURCE.

1.Before tracking the blade, make sure the blade guides and blade support bearings are clear of the blade so as not to interfere with the tracking adjustment. Also make sure that the blade is tensioned properly. (Refer to section “ADJUSTING BLADE TENSION”).

2.Open the hinged door (C) Fig. 20.

3.Rotate upper wheel (A) Fig. 20, clockwise by hand and check to see if the blade (B) rides true on the approximate center of the two wheels.

4.If an adjustment is necessary, SLIGHTLY turn blade tracking knob (D) Fig. 19, clockwise to move the blade to the rear, and counterclockwise to move the blade to the front. NOTE: Turn the blade tracking knob (D) in small intervals to adjust the blade tracking.

ADJUSTING UPPER BLADE GUIDE ASSEMBLY

The upper blade guide assembly (A) Fig. 21, should always be no more than 1/8 in. above or as close as possible to the top surface of the workpiece being cut.

Loosen knob (B) Fig. 21, rotate knob (C) and position the guide assembly (A) to the desired position. Then tighten knob (B).

A

B

C

D

Fig. 19

C

B

A

Fig. 20

C B

A

Fig. 21

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Catalog no BDBS100 Inch 229MM Bench Band SAWSafety Guidelines Definitions General Safety Rules Important Safety InstructionsDON’T Force the Workpiece on the Machine Additional Safety Rules for for Band SawsGrounding Instructions Power ConnectionsMinimum Gauge Extension Cord Unpacking and CleaningExtension Cords Operating InstructionsIN. Bench Band SAW Parts Closing Door Assembly Assembling Table To MachinePage Fastening Band SAW To Supporting Surface Attaching Lamp to MachineOpening and Closing Door Operating Controls and AdjustmentsLocking Switch OFF Position Starting Stopping SAWTracking the Blade Adjusting Blade TensionAdjusting Upper Blade Guide Assembly Adjusting Upper Blade Guides and Blade Support Bearing Tilting the Table Adjusting Lower Blade Guides and Blade Support BearingAdjusting the Table Positive Stops Adjusting Belt TensionCarefully Turn Blade Inside OUT Changing BladesDust Chute Wrench StorageCutting Curves Operating the Band SAWMiter Guage Optional Page Probable Cause Remedy Troubleshooting GuideBand SAW Blades Service Information Full TWO-YEAR Home USE Warranty MaintenanceAccessories Catálogo N BDBS100 Sierra de Cinta de 9 pulg Para BanquilloPautas DE SEGURIDAD/DEFINICIONES Normas Generales DE SeguridadInstrucciones Importantes Sobre Seguridad Utilice EL Cordón DE Extensión Adecuado Reglas DE Seguridad Adicionales Para LAS Sierras DE CintaGuarde Estas Instrucciones Conexiones a LA Fuente DE Alimentación Prefacio Cordones DE ExtensiónInstrucciones DE Funcionamiento Cordón DE Extensión DE Calibre MínimoMontaje DE LA Lampara a LA Maquina MontajePartes DE LA Sierra DE LA Venda DEL Banco 9 Pulg Montaje DE LA Mesa a LA MaquinaControles DE Funcionamiento Y Ajustes Aviso Se muestra el protector de hoja superior Inclinando LA MesaOperacion DE LA Sierra DE Cinta Conducto DE PolvoCausa probable Guia DE Localizacion DE AveriasContinuacion Hojas DE Sierra DE CintaGarantía Completa DE DOS Años Para USO EN EL Hogar AccesoriosMantenimiento Información DE MantenimientoDE Catalogue BDBS100 Conserver CE Mode D’EMPLOI Pour UN Usage UltérieurLignes Directrices EN Matière DE Sécurité Définitions Règles Générales DE SécuritéDirectives DE Sécurité Importantes Réduire LE Risque DE Démarrage Règles DE Sécurité Supplémentaires Pour LES Scies À RubanDirectives DE Mise À LA Terre Connexions ÉlectriquesFig. a Duree Estimee Pour L’ASSEMBLAGE Rallonges ÉlectriquesDescription Fonctionnelle Outils Nécessaires Pour L’ASSEMBLAGEFixer LA Lampe À Lappareil Pièces DE LA Scie À Lame Ruban DEAssemblage Assemblage DE LA Table À LA MachineRéglage LA Tension DE LA Lame Utilisation DES Commandes ET RéglagesDémarrage ET Arrêt DE LA Scie Ouvrir ET Fermer LA PorteRéglage DES Butées Fixes DE LA Table Inclinaison DE LA TableUtilisation DE LA Scie À Lame Ruban Guide DE Dépannage Cause probable SolutionLames DE Scie À Lame Ruban Guide DE DépannageGarantie Complète DE Deux ANS Pour Usage Résidentiel AccessoiresInformation SUR LES Services Entretien

BDBS100 specifications

The Black & Decker BDBS100 is a versatile and innovative cordless screwdriver designed for a variety of applications, making it an essential tool for both DIY enthusiasts and professionals. This power-packed tool combines exceptional performance with user-friendly features.

One of the standout characteristics of the BDBS100 is its compact and lightweight design. Weighing in at just under two pounds, it can be easily maneuvered in tight spaces without causing user fatigue during extended use. The ergonomic handle provides a comfortable grip, allowing for better control and precision while driving screws.

The BDBS100 is equipped with a powerful motor that delivers a maximum torque of 180 in-lbs, making it suitable for a range of materials, from wood to metal. With its variable speed settings, users can adjust the output to meet the demands of different tasks, ensuring optimal performance every time. The built-in LED work light is a convenient feature that illuminates dark work areas, enabling users to see their work clearly, especially in tight or dimly lit spaces.

One of the most significant advantages of the BDBS100 is its lithium-ion battery technology. The 1.5Ah battery provides longer runtime and faster charging compared to traditional nickel-cadmium batteries. Users can expect approximately 18 months of battery life due to the built-in battery management system, which helps to extend the battery’s lifespan by preventing overcharging and overheating.

The screwdriver comes with an adjustable clutch that allows users to select the appropriate torque setting for various applications, minimizing the risk of stripping screws or damaging work materials. Additionally, the BDBS100 includes a magnetic bit holder that keeps bits securely in place, preventing them from falling or getting lost during use.

With its combination of performance, portability, and advanced features, the Black & Decker BDBS100 is an excellent addition to any tool collection. Whether you are assembling furniture, performing home repairs, or tackling other tasks, this cordless screwdriver provides the power and convenience needed to complete projects efficiently and effectively. Its thoughtful design and robust capabilities make it a reliable choice for a wide range of users seeking a dependable tool.
Top Page Image Contents