Black & Decker BDBS100 Adjusting Lower Blade Guides and Blade Support Bearing, Tilting the Table

Page 13

ADJUSTING LOWER BLADE GUIDES AND BLADE SUPPORT BEARING

The lower blade guides and blade support bearing should be adjusted at the same time as the upper guides and support bearings as follows:

WARNING: DISCONNECT MACHINE FROM POWER SOURCE.

1. Loosen two screws (A) Fig. 24, and move guides

(B) as close as possible to the sides of the blade, being

careful not to pinch the blade. Then tighten the two

screws (A).

E

G

AB

F

D

C

A

2. The front edge of guide blocks (B) Fig. 24, should

be adjusted so they are just behind the “gullets” of the

blade teeth by loosening screw (C), and moving

assembly (D) in or out as necessary. Then tighten

screw (C).

3. The lower blade support bearing (E) Fig. 24, should

be adjusted to support the rear of the blade during the

cutting operation and also prevent the blade from being

pushed too far to the rear which could damage the

blade. The support bearing (E) Fig. 24, should be set

about 1/32 in. behind the blade by loosening screw (F)

Fig. 24, and moving shaft (G) in or out. Then tighten

screw (F).

4. The lower blade support bearing (E) Fig. 24, should

also be adjusted so the back of the blade overlaps the

outside diameter of the ball bearing by approximately

1/8 in. The blade support bearing (E) is set on an

eccentric shaft.To change position of bearing (E),

loosen screw (F) Fig. 24, and rotate shaft (G) Figs. 24

and 25, until the blade properly overlaps the support

bearing. Then tighten screw (F) Fig. 24.

TILTING THE TABLE

The table can be tilted 45 degrees to the right. To tilt the table, loosen lock handle (A) Fig. 26, and turn knob (B) clockwise until desired angle is established. Then tighten lock handle (A). NOTE: The table lock handle

(A)can be repositioned by pulling out on the handle and repositioning it on the nut located underneath the hub of the handle. A scale (C) and pointer (D) are provided to indicate the degree of tilt.

Fig. 24

G

Fig. 25

E

A

B C D

Fig. 26

13

Image 13
Contents Catalog no BDBS100 Inch 229MM Bench Band SAWSafety Guidelines Definitions General Safety Rules Important Safety InstructionsDON’T Force the Workpiece on the Machine Additional Safety Rules for for Band SawsGrounding Instructions Power ConnectionsExtension Cords Unpacking and CleaningOperating Instructions Minimum Gauge Extension CordIN. Bench Band SAW Parts Closing Door Assembly Assembling Table To MachinePage Fastening Band SAW To Supporting Surface Attaching Lamp to MachineLocking Switch OFF Position Operating Controls and AdjustmentsStarting Stopping SAW Opening and Closing DoorAdjusting Upper Blade Guide Assembly Adjusting Blade TensionTracking the Blade Adjusting Upper Blade Guides and Blade Support Bearing Tilting the Table Adjusting Lower Blade Guides and Blade Support BearingAdjusting the Table Positive Stops Adjusting Belt TensionDust Chute Changing BladesWrench Storage Carefully Turn Blade Inside OUTMiter Guage Optional Operating the Band SAWCutting Curves Page Probable Cause Remedy Troubleshooting GuideBand SAW Blades Accessories MaintenanceService Information Full TWO-YEAR Home USE Warranty Catálogo N BDBS100 Sierra de Cinta de 9 pulg Para BanquilloInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadPautas DE SEGURIDAD/DEFINICIONES Utilice EL Cordón DE Extensión Adecuado Reglas DE Seguridad Adicionales Para LAS Sierras DE CintaGuarde Estas Instrucciones Conexiones a LA Fuente DE Alimentación Instrucciones DE Funcionamiento Cordones DE ExtensiónCordón DE Extensión DE Calibre Mínimo PrefacioPartes DE LA Sierra DE LA Venda DEL Banco 9 Pulg MontajeMontaje DE LA Mesa a LA Maquina Montaje DE LA Lampara a LA MaquinaControles DE Funcionamiento Y Ajustes Aviso Se muestra el protector de hoja superior Inclinando LA MesaOperacion DE LA Sierra DE Cinta Conducto DE PolvoCausa probable Guia DE Localizacion DE AveriasContinuacion Hojas DE Sierra DE CintaMantenimiento AccesoriosInformación DE Mantenimiento Garantía Completa DE DOS Años Para USO EN EL HogarDE Catalogue BDBS100 Conserver CE Mode D’EMPLOI Pour UN Usage UltérieurDirectives DE Sécurité Importantes Règles Générales DE SécuritéLignes Directrices EN Matière DE Sécurité Définitions Réduire LE Risque DE Démarrage Règles DE Sécurité Supplémentaires Pour LES Scies À RubanDirectives DE Mise À LA Terre Connexions ÉlectriquesFig. a Description Fonctionnelle Rallonges ÉlectriquesOutils Nécessaires Pour L’ASSEMBLAGE Duree Estimee Pour L’ASSEMBLAGEAssemblage Pièces DE LA Scie À Lame Ruban DEAssemblage DE LA Table À LA Machine Fixer LA Lampe À LappareilDémarrage ET Arrêt DE LA Scie Utilisation DES Commandes ET RéglagesOuvrir ET Fermer LA Porte Réglage LA Tension DE LA LameRéglage DES Butées Fixes DE LA Table Inclinaison DE LA TableUtilisation DE LA Scie À Lame Ruban Guide DE Dépannage Cause probable SolutionLames DE Scie À Lame Ruban Guide DE DépannageInformation SUR LES Services AccessoiresEntretien Garantie Complète DE Deux ANS Pour Usage Résidentiel

BDBS100 specifications

The Black & Decker BDBS100 is a versatile and innovative cordless screwdriver designed for a variety of applications, making it an essential tool for both DIY enthusiasts and professionals. This power-packed tool combines exceptional performance with user-friendly features.

One of the standout characteristics of the BDBS100 is its compact and lightweight design. Weighing in at just under two pounds, it can be easily maneuvered in tight spaces without causing user fatigue during extended use. The ergonomic handle provides a comfortable grip, allowing for better control and precision while driving screws.

The BDBS100 is equipped with a powerful motor that delivers a maximum torque of 180 in-lbs, making it suitable for a range of materials, from wood to metal. With its variable speed settings, users can adjust the output to meet the demands of different tasks, ensuring optimal performance every time. The built-in LED work light is a convenient feature that illuminates dark work areas, enabling users to see their work clearly, especially in tight or dimly lit spaces.

One of the most significant advantages of the BDBS100 is its lithium-ion battery technology. The 1.5Ah battery provides longer runtime and faster charging compared to traditional nickel-cadmium batteries. Users can expect approximately 18 months of battery life due to the built-in battery management system, which helps to extend the battery’s lifespan by preventing overcharging and overheating.

The screwdriver comes with an adjustable clutch that allows users to select the appropriate torque setting for various applications, minimizing the risk of stripping screws or damaging work materials. Additionally, the BDBS100 includes a magnetic bit holder that keeps bits securely in place, preventing them from falling or getting lost during use.

With its combination of performance, portability, and advanced features, the Black & Decker BDBS100 is an excellent addition to any tool collection. Whether you are assembling furniture, performing home repairs, or tackling other tasks, this cordless screwdriver provides the power and convenience needed to complete projects efficiently and effectively. Its thoughtful design and robust capabilities make it a reliable choice for a wide range of users seeking a dependable tool.