Black & Decker QP1020LK Pocket Cutting, Wrench Storage, Ripping, Maintenance, Lubrication

Page 11

633145-02,01 QP1020LK 12/16/05 1:20 PM Page 11

POCKET CUTTING

POCKET CUTTING IS USED TO CUTA HOLE IN APIECE OF MATERIAL WITHOUT CUTTING FROM THE SIDE.

•Measure and mark work.

•Tilt saw forward and rest front of the shoe on material to be cut. Align so that cut will begin at the back of the drawn rectangle shown in figure19.

19

•Using the retracting lever, retract blade guard to an upward position, with the blade just clearing the material, start motor and gradually lower the saw into the material.

WARNING: As blade starts cutting the material, release the retracting lever immediately.

•Never tie the blade guard in a raised position.

•When the shoe rests flat on the material being cut, complete the cut in forward direction.

•Allow the blade to come to a complete stop before lifting saw from material.

•When starting each new cut, repeat the above steps.

WRENCH STORAGE

The blade wrench can be stored on the saw shoe as shown in figure 20.

20

RIPPING

Your saw is not equipped with a rip fence. If installing a rip fence, insure the fence fits snug in slots.

If you do not have a proper fitting fence, use a straight edge guide in contact with the edge of the shoe to improve accuracy of cut and reduce the possibility of binding and kickback.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

LUBRICATION

Black & Decker tools are properly lubricated at the factory and are ready for use.

ACCESSORIES

Recommended accessories for use with your tool are available from your local retailer.

WARNING:The use of any accessory not recommended for use with this tool could be hazardous. Use only 7-1/4 “ (184mm) blades with 5/8” diameter arbor. Exception: 7" (175 mm) abrasive blades can be used.

When cutting metal, be careful of hot sparks which are thrown by the blade.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents VEA EL Español EN LA Contraportada 4 184mm Circular Saw With Removable LaserWork Area General Safety RulesElectrical Safety Personal SafetyService Specific Safety RulesCauses and Operator Prevention of Kickback SE These Instructions Additional Safety Rules Circular Saws633145-02,01 QP1020LK 12/16/05 120 PM To Reduce the Risk of Kickback Safety Instructions LasersGuard Against Kickback Motor Assembly / Adjustment SET-UPCutting Depth Adjustment Operating Instructions Bevel Angle AdjustmentSwitch Kerf Plate AdjustmentTo USE Laser Line on SAW Installing the BatteriesLaser Switch Laser LineTo USE Laser OFF SAW For the angles created when using the laser in these holesWrench Storage MaintenanceAccessories Pocket CuttingFull TWO Year Warranty Service InformationSécurité Personnelle Règles Générales DE SécuritéZone DE Travail Sécurité EN ÉlectricitéRéparation Règles DE Sécurité SpécifiquesUtilisation ET Entretien DE L’OUTIL Performances et la sécurité de fonctionnement.V Effets DE Rebond PROTÉGEZ-VOUS DES Effets DE Rebond Pour Réduire LE Risque D’EFFET DE Rebond Directives DE Sécurité LasersRéglage DE Profondeur DE Découpe Configuration DE ’ASSEMBLAGE ET DES RéglasesMoteur Interrupteur Directives D’UTILISATIONRéglage DE L’ANGLE DE Biseau Fixation ET Dépose DE LA LameRéglage DE LA Plaque DE Trait DE Scie Installation DES PilesRaie Laser Utilisation DU Laser Hors DE LA Scie Interrupteur DU LaserPour Utiliser LA Raie Laser SUR LA Scie Entretien Découpe EN PocheRangement DE LA CLÉ Sciage RapideGarantie Complète DE Deux ANS AccessoiresGraissage Information SUR LES RéparationsSeguridad Personal InstruccionesÁrea DE Trabajo Seguridad EléctricaMantenimiento Normas DE Seguridad EspecíficasUSO Y Cuidado DE LA Herramienta Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Normas DE Seguridad Adicionales Sierras Circulares Conserve Estas InstruccionesPara Reducir EL Riesgo DE Retroceso Instruccciones DE Seresseguridad Láseres Regulación DE LA Profundidad DE Corte ENSAMBLADO/REGULACIONRegulación DE LA Placa DE Corte Instrucciones DE OperaciónInterruptor Instalación DE LAS Baterías Línea LáserUSO DEL Láser Fuera DE LA Sierra Interruptor DEL LáserUSO DE LA Línea Láser EN LA Sierra Accesorios Corte InternoCortes Longitudinales LubricaciónInformación DE Servicio MEXICO, D.F CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL PUEBLA, PUE633145-02,01 QP1020LK 12/16/05 120 PM

QP1020LK specifications

The Black & Decker QP1020LK is a versatile and innovative tool designed to meet the demands of both DIY enthusiasts and professionals alike. This powerful oscillating multi-tool is known for its efficiency and user-friendly features, making it an essential addition to any toolkit.

One of the standout features of the QP1020LK is its powerful 2.0 amp motor, which provides ample power for a variety of applications. Whether you're sanding, scraping, or cutting through different materials, this tool delivers consistent performance. The variable speed settings allow users to adjust the tool's speed from 10,000 to 22,000 oscillations per minute, ensuring optimal results for various tasks.

The QP1020LK uses a tool-free accessory change system. This means switching attachments is quick and easy, reducing downtime and increasing productivity. The inclusive 20-piece accessory kit offers a wide range of blades and pads designed for cutting wood, drywall, and metal, as well as sanding and scraping applications. This versatility ensures that users have the right tools for their specific projects at hand.

Another important aspect of the Black & Decker QP1020LK is its ergonomic design. The tool features a comfortable grip that enhances maneuverability and reduces fatigue over extended periods of use. Additionally, the compact design allows for easy access to tight spaces, making it ideal for intricate jobs where larger tools would be cumbersome.

The QP1020LK also incorporates innovative cooling technology, which allows the tool to operate efficiently without overheating. This is especially important during arduous tasks, as it contributes to the longevity and durability of the tool.

Safety is always a priority, and the Black & Decker QP1020LK is designed with user protection in mind. Its integrated safety features prevent accidental starts, ensuring users can work confidently.

In summary, the Black & Decker QP1020LK is a standout oscillating multi-tool characterized by its powerful motor, variable speed settings, tool-free accessory changes, and ergonomic design. With a comprehensive accessory kit and enhanced safety features, this tool is well-equipped to handle a wide array of projects, making it a must-have for anyone looking to enhance their DIY capabilities. Whether you are a novice or a seasoned professional, the QP1020LK offers the reliability and performance needed to tackle jobs of any scale.
Top Page Image Contents