Black & Decker instruction manual 633145-02,01 QP1020LK 12/16/05 120 PM

Page 5

633145-02,01 QP1020LK 12/16/05 1:20 PM Page 5

of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

•Snagging the lower guard on a surface below the material being cut can momentarily reduce operator control. The saw can lift partially out of the cut increasing the chance of blade twist. Ensure there is sufficient clearance under the workpiece.

•When necessary to raise lower guard manually, use the retracting lever.

•KEEP THE BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback. The use of dull and/or dirty blades can increase the saw loading causing the operator to push harder which promotes twisting.

DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Never place hands in front of or behind the path of the blade while cutting. Do not reach underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving.

•SUPPORT LARGE PANELS. Large panels must be supported as shown (figure 1) in this manual to minimize the risk of blade pinching and kickback. Material supported only at the ends (figure 2) will lead to blade pinching. When cutting operation requires the resting of the saw on the workpiece, the saw shall be rested on the larger portion and the smaller piece cut off.

1

2

•USE ONLY CORRECT BLADES AND BLADE ASSEMBLY COMPONENTS WHEN MOUNTING BLADES. Do not use blades with incorrect size holes.

Never use defective or incorrect blade washers or bolts. Follow blade assembly procedures.

•ADJUSTMENTS. Before cutting be sure depth and bevel adjustments are tight.

•SUPPORT AND SECURE THE WORK PROPERLY. Insure that the material to be cut is clamped (figure 3) and solidly supported and balanced on a strong, stable and level work surface. Support the work so that the wide portion of the saw shoe is on the portion of the material that doesn’t fall after the cut is made. Never hold cut off piece by hand (figure 4 ). KICKBACK from blade pinch can result. Keep both hands on saw at all times.

3

4

45

15

0

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents VEA EL Español EN LA Contraportada 4 184mm Circular Saw With Removable LaserElectrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesCauses and Operator Prevention of Kickback SE These Instructions Additional Safety Rules Circular Saws633145-02,01 QP1020LK 12/16/05 120 PM To Reduce the Risk of Kickback Safety Instructions LasersGuard Against Kickback Motor Assembly / Adjustment SET-UPCutting Depth Adjustment Switch Bevel Angle AdjustmentKerf Plate Adjustment Operating InstructionsLaser Switch Installing the BatteriesLaser Line To USE Laser Line on SAWTo USE Laser OFF SAW For the angles created when using the laser in these holesAccessories MaintenancePocket Cutting Wrench StorageFull TWO Year Warranty Service InformationZone DE Travail Règles Générales DE SécuritéSécurité EN Électricité Sécurité PersonnelleRéparation Règles DE Sécurité SpécifiquesUtilisation ET Entretien DE L’OUTIL Performances et la sécurité de fonctionnement.V Effets DE Rebond PROTÉGEZ-VOUS DES Effets DE Rebond Pour Réduire LE Risque D’EFFET DE Rebond Directives DE Sécurité LasersRéglage DE Profondeur DE Découpe Configuration DE ’ASSEMBLAGE ET DES RéglasesMoteur Réglage DE L’ANGLE DE Biseau Directives D’UTILISATIONFixation ET Dépose DE LA Lame InterrupteurRéglage DE LA Plaque DE Trait DE Scie Installation DES PilesRaie Laser Utilisation DU Laser Hors DE LA Scie Interrupteur DU LaserPour Utiliser LA Raie Laser SUR LA Scie Rangement DE LA CLÉ Découpe EN PocheSciage Rapide EntretienGraissage AccessoiresInformation SUR LES Réparations Garantie Complète DE Deux ANSÁrea DE Trabajo InstruccionesSeguridad Eléctrica Seguridad PersonalMantenimiento Normas DE Seguridad EspecíficasUSO Y Cuidado DE LA Herramienta Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Normas DE Seguridad Adicionales Sierras Circulares Conserve Estas InstruccionesPara Reducir EL Riesgo DE Retroceso Instruccciones DE Seresseguridad Láseres Regulación DE LA Profundidad DE Corte ENSAMBLADO/REGULACIONRegulación DE LA Placa DE Corte Instrucciones DE OperaciónInterruptor Instalación DE LAS Baterías Línea LáserUSO DEL Láser Fuera DE LA Sierra Interruptor DEL LáserUSO DE LA Línea Láser EN LA Sierra Cortes Longitudinales Corte InternoLubricación AccesoriosInformación DE Servicio GUADALAJARA, JAL CULIACAN, SIN MONTERREY, N.LPUEBLA, PUE MEXICO, D.F633145-02,01 QP1020LK 12/16/05 120 PM

QP1020LK specifications

The Black & Decker QP1020LK is a versatile and innovative tool designed to meet the demands of both DIY enthusiasts and professionals alike. This powerful oscillating multi-tool is known for its efficiency and user-friendly features, making it an essential addition to any toolkit.

One of the standout features of the QP1020LK is its powerful 2.0 amp motor, which provides ample power for a variety of applications. Whether you're sanding, scraping, or cutting through different materials, this tool delivers consistent performance. The variable speed settings allow users to adjust the tool's speed from 10,000 to 22,000 oscillations per minute, ensuring optimal results for various tasks.

The QP1020LK uses a tool-free accessory change system. This means switching attachments is quick and easy, reducing downtime and increasing productivity. The inclusive 20-piece accessory kit offers a wide range of blades and pads designed for cutting wood, drywall, and metal, as well as sanding and scraping applications. This versatility ensures that users have the right tools for their specific projects at hand.

Another important aspect of the Black & Decker QP1020LK is its ergonomic design. The tool features a comfortable grip that enhances maneuverability and reduces fatigue over extended periods of use. Additionally, the compact design allows for easy access to tight spaces, making it ideal for intricate jobs where larger tools would be cumbersome.

The QP1020LK also incorporates innovative cooling technology, which allows the tool to operate efficiently without overheating. This is especially important during arduous tasks, as it contributes to the longevity and durability of the tool.

Safety is always a priority, and the Black & Decker QP1020LK is designed with user protection in mind. Its integrated safety features prevent accidental starts, ensuring users can work confidently.

In summary, the Black & Decker QP1020LK is a standout oscillating multi-tool characterized by its powerful motor, variable speed settings, tool-free accessory changes, and ergonomic design. With a comprehensive accessory kit and enhanced safety features, this tool is well-equipped to handle a wide array of projects, making it a must-have for anyone looking to enhance their DIY capabilities. Whether you are a novice or a seasoned professional, the QP1020LK offers the reliability and performance needed to tackle jobs of any scale.
Top Page Image Contents