Carrier 06D specifications Removing Pump End Bearing Head

LEGEND FOR FIG. 12

1	— Motor Cover Gasket	17	— Oil Drain Plug	34	— Oil Ring
2	— Motor End Cover	18	— Crankcase	35	— Compression Rings
3	— Discharge Manifold Connection	19	— Bottom Plate Gasket	36	— Eccentric Strap
4	— Valve Plate Gasket	20	— Bottom Plate	37	— Eccentric Strap Side Shield
5	— Valve Plate Assembly	21	— Bottom Plate Washer and Cap Screw	38	— Pump End Counterweight
6	— Cylinder Head Gasket	22	— Oil Filter Screen	39	— Oil Pump Drive Segment
7	— Cylinder Head	23	— Oil Return Check Valve	40	— Drive Segment Cap Screws
8	— Cylinder Head Washer	24	— Oil Level Sight Glass		and Lockwashers
	and Cap Screw	25	— Motor Terminal Plate	41	— Oil Feed Guide
9	— Suction Manifold Connection*	26	— Dowel Pins (For Suction Valve	42	— Oil Feed Guide Retainer Spring
10	— Suction Valve Positioning Spring		Positioning)	43	— Cover Gasket
11	— Suction Strainer	27	— Equalizing Tube and Lock Screw Assembly	44	— Pump Cover Cap Screw and Washer
12	— Bearing Head Gasket	28	— Lockwasher	45	— Counterweight Bolt
13	— Oil Pump Inlet Passage	29	— Rotor Lockwasher	46	— Eccentric Strap Side Shield
14	— Bearing Head Washer	30	— Rotor Drive Key	47	— Motor End Counterweight
	and Cap Screw	31	— Piston Pin Lock Ring	48	— Locknut
15	— Oil Pump Cover	32	— Piston Pin	49	— Eccentric Shaft (or Crankshaft)
16	— Pump End Bearing Head	33	— Piston	*Used to add compressor oil.

1

2

3

4

5

8

6

7

LEGEND

1	— Suction Strainer	5	— Oil Pump Rotor
	Assembly	6	— Drive Segment Cap
2	— Oil Pump Bearing Head		Screws
	Assembly	7	— Bearing Head Cap
3	— Rotor Retaining Ring		Screws
4	— Oil Pump Drive Segment	8	— Oil Pump Inlet Passage

Three Allen head cap screws hold capacity control valve in place (Fig. 14). Remove screws using a cut-down 3/16-in. Allen wrench, and pull valve from cylinder head.

Remove same number of piston plugs from replacement compressor as number of unloaders supplied with original compressors. Three Allen head cap screws hold piston plug assembly in place. Remove flange cover, gasket, spring and bypass piston plug (Fig. 15). A tapped hole is provided in piston to allow it to be pulled out. Hole has same thread diameter as cap screws removed above.

CAPACITY

CONTROL

VALVE

CAP SCREWS (NONINTERCHANGEABLE WITH FLANGE COVER CAP SCREWS)

Fig. 13 — Removing Pump End Bearing Head

Cylinder Heads — Disassemble cylinder heads by re- moving cap screws and prying up on side between cylinder head and valve plate to break heads loose from valve plate. Do not strike cylinder heads to break loose.

Check heads for warping, cracks and damage to gasket surfaces. When replacing cylinder head, torque cap screws 30 to 35 lb-ft to prevent high to low side leak in center portion of cylinder head gasket.

Service Replacement Compressors — Replace- ment compressors are not equipped with control valves. One or both side bank cylinder head(s) is plugged with a spring loaded plug piston assembly. Compressor will run fully loaded with piston plug(s) in place.

Transfer original capacity control valve(s) to replacement compressor (ensures proper valves are used with correct set- ting). For sealing purposes, install a plug piston assembly into each cylinder head of original compressor from which a con- trol valve was removed.

Fig. 14 — Removal of Capacity Control Valve

BYPASS PISTON PLUG

SPRING

CAP SCREWS (NONINTERCHANGERABLE WITH CONTROL VALVE CAP SCREWS)

TAB

GASKET

GAS PORT

FLANGE COVER

Fig. 15 — Removal of Bypass Piston Plug

14