Craftsman 113.298721, 113.298761 manual Crosscutting, Auxiliary Panel Work Support, Ywood

Page 31

AUXILIARY PANEL WORK SUPPORT

Make using a piece of 3/4" and 3/8" plywood. Fasten together wtih glue and wood screws. Use this Auxiliary

Panel Work Support only when cutting large panels that

require the Rip Fence to be positioned past the exposed side of the extension.

.YWOOD

3-5/8

FACE & EDGE

MUST BE

PARALLEL

3/8 PLYWOOD

NOTE: All dimension in inches

AUXILIARY PANEL/WORK SUPPORT

CROSSCUTTING

Crosscut- A cutting or shaping operation made across the width of the workpiece.

The graduations on the Miter Gauge provide accuracy

lor average woodworking. In some cases where ex- treme accuracy is required, when making angle cuts, for example, make a trial cut and then recheck it with an accurate square, or protractor.

If necessary, the Miter Gauge head can be swiveled slightly to compensate for any inaccuracy.

NOTE: The space betweenthe Miter Gauge Bar andthe groove in the table isheld to a minimum dudng manufac- turing.

For maximum accuracy when using the Miter Gauge, always '1avor"one side of the groove in the table. In other words, don'tmove the Miter Gauge from side to side while cutting, but keep one side of the bar riding against one side of the groove.

NOTE: Glue a piece of sandpaperto the face ofthe Miter Gauge head. This will help prevent the workpiece from "creeping" while it is being cut.

The Hold-Down Clamp (optional accessory) should be used on the Miter Gauge for greater accuracy.

The Miter Gauge may be used in either of the grooves in

When cutting long workpieces, invert Auxiliary Panel/ Work Support and position it on top of the Guide Bars to support the workpiece as near to the end as possible. If this does not adequately supportthe workpiece, you can make a simple support by clamping a piece of plywood to a sawhorse. (See illustration above)

Use the Hold-Down Clamp (optional accessory) on the Miter Gauge for greater accuracy.

._SANDPAPER

the table. Make sure it is locked.

WARNING: To avoid blade contact or kickback, hold the Miter Gauge properly.

When using the Miter Gauge in the LEFT hand groove, hold the workpiece firmly against the Miter Gauge head with your left hand, and grip the lock handle with your right.

When using the RIGHT hand groove, hold the work- piece with yourright hand and the Lock Handle with your left hand.

\

\

AUXILIARY FENCE/

WORK SUPPORT

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Part No. SP5396 Instructions CarefullyBefore Each USE Full ONE Year Warranty on Craftsman Table SAWBefore Using the SAW When Installing or Moving the SAWWear Your Kerfs about 5/16 Apart Whenever SAW Blade is SpinningTurn the saw off Additional iNSTRUCTIONS forBefore Starting Before Leaving the SAWConnecting to Power Source Outlet Motor specifications and electrical requirementsGlossary of terms for woodworking Contents Unpacking and checking contents Following items Spacer, Rip Fence Guide Bar Part Name QTYAB AC AD AE Afag AH Checking Table Insert Installing HandwheelsChecking Blade Squareness to Assembung Steel Legs External AssemblyInstall screws, washers, Iockwashers and nuts as shown Attaching and Assembling Table Extensions16-18 x 3/4 HEX Head Screw 2t/64 tN Washer Mounting SwitchHEX NUT Lock Washer 5116-18 x 3/4 Instalung Right Front RiP Fence Guide BAR16-18 x 3/4 HEX NU External Lockwasher HEX Head Screw16-18 x 1 Flat WasherRear Fence Guide BAR Bracket Extension 7TH Slot 5TH Slot 1ST Slot HEX Head Screw8THICKNESSES of Paper Aligning RiP Fence Self Aligning Spring AdjustmentRiP Fence Alignment Adjustment Installing Blade Guard Adjusting RiP Scale PointerLockwash ER EmDOFROD AssembyKEY Mounting the Motor16IN. Wrench Make Sure Keyis Removed from ShaftSetscrew Instalung BeltPositioning Motor on Motor Mounting Base Mounting Motor on Motor BaseSUPPO...ACKET Installing Belt GuardFrom among the loose parts find 2 Wire Ties INSTALLiNG Belt GuardPlugging iN Motor Sawblade ON-OFF SwitchAuthorizedand Possible Hazardous USE by Children and Others Getting to know your saw Blade Guard not Shown For Picture Clarity Picture Clarify Removing and iNSTALLiNGSawblade EXACT-I-CUTBefore Each USE Safety instructions for basic saw operationsWhenever SAW Blade is Spinning Basic saw operation using the miter gauge Safety for basic saw operationsWork Helpers Parallel Plywood Auxiliary PANEL/WORK Support CrosscuttingAuxiliary Panel Work Support YwoodRight Basic saw operationRepetitive Cutting Miter curiINGCompound Miter Cutting Using the rip fenceADDmONAL Safety Instructions for Bevel CrosscuttingRipping Using Featherboards for Thru SawingBevel RiPPiNG Helpers RESAWlNGRabbeting Cutting PanelsMolding Cutting Using Featherboards for NON Thru SawingBack of SAW Miter Gauge AdjustmentsFront Trunnion Rear Trunnion REAR-TRUNNION Screws Blade TILT, or Squareness of Blade to Table PositionTeeth Nut inside using a 3/8 inch wrenchAd ustments Tilt MechanismSears recommends the following accessories MaintenanceTrouble Probable Cause Trouble Shooting GeneralTroubleshooting Motor Trouble Probable CauseremedyTrouble Troubleshooting Motor ContdRepair parts =g$ Repair parts Page KEY Part Description Parts LiST for Craftsman 10 Inch Table SAW Model 113.298721Kiey Part Description PARTs LiST for Craftsma 10 iNCH Table SAW16-18 x 1-1t4 Repair Parts Model !13.298721 Parts List for Craftsman 10 Inch Table SAWGuard Assembly Hardware for Attaching Legs to SAW LEG SETINCH Table SAW

298721, 113.298721, 113.298761 specifications

The Craftsman 298721, also known by its model numbers 113.298721 and 113.298761, represents a well-crafted power tool that has gained popularity among DIY enthusiasts and professionals alike. This versatile tool is designed to facilitate a variety of woodworking and construction tasks, making it an invaluable addition to any workshop.

One of the standout features of the Craftsman 298721 is its robust build quality. Crafted from durable materials, this tool is designed to withstand the rigors of heavy use. Its sturdy construction not only ensures longevity but also enhances user safety, as it can endure demanding tasks without compromising performance.

Equipped with a powerful motor, the Craftsman 298721 delivers consistent performance across various applications. The high horsepower ensures that it can easily handle tough materials, allowing users to make precise cuts and achieve desired outcomes effortlessly. The motor is also designed to operate quietly, mitigating the noise commonly associated with power tools and providing a more pleasant working environment.

Another notable characteristic is its user-friendly design. The tool features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended periods of use. This attention to ergonomics is evident in the lightweight build, making it easier for users to maneuver the tool with ease.

In terms of technology, the Craftsman 298721 incorporates advanced features that enhance its usability. One such feature is its adjustable speed control, allowing users to tailor the tool's performance to specific tasks. This adaptability makes it suitable for a wide range of applications, from intricate detail work to heavier cutting jobs.

The tool's compatibility with various attachments further extends its utility. Users can easily switch between different blades and accessories, enabling them to tackle diverse projects without the need for multiple tools. This flexibility makes the Craftsman 298721 a cost-effective solution for those looking to streamline their workshop.

Additionally, the safety mechanisms integrated into the Craftsman 298721 ensure that users can operate the tool confidently. Features such as blade guards and lock-off switches provide an extra layer of protection, reducing the risk of accidents while working.

In summary, the Craftsman 298721, alongside its model numbers 113.298721 and 113.298761, is a versatile and reliable power tool that combines robust construction, powerful performance, user-friendly features, and advanced technology. Whether for professional contractors or home improvement enthusiasts, this tool stands out as an essential asset for any workshop.
Top Page Image Contents