Craftsman 298721 manual Basic saw operation, Repetitive Cutting, Miter curiING, Right

Page 32

basic saw operation

REPETITIVE CUTTING

REPETITIVE CUTTING is known as cutting a quantity of pieces the same length without having to mark each

piece.

1.Use the Stop Rods (optional accessory) only for cutting duplicate pieces 6 inches long and longer.

2.Foitow all safety precautions and operational instruc- tions for cross cutting.

When making repetitive cuts from a long workpiece, make sure it is adequately suppoded.

Use the Hold-Down Clamp (optional accessory) on the Miter Gauge for greater accuracy.

i

i

3.NEVER USE THE RIP FENCE AS A LENGTH STOP BECAUSE THE CUT-OFF PIECE COULD BIND BETWEEN THE FENC EAN D THE BLADE CA USIN G A KICKBACK.

4.When making repetitive cuts shorter than 6 inches, clamp a block ofwood 2 inches long to the table to act as a length stop. Do not clamp directly to the bottom edge of the table because the "swivel" of the clamp will not grip properly. Place a small block of wood between the bottom edge of the table and the "C" clamp,

CAUTION: When clamping the block, make sure that the end of the block Is well In front of the

sawblade. Be sure it is clamped securely.

5.SrK:lethe workpiece along the Miter Gauge unt_ it touches the block, hold itsecurely or clamp itwith the Hold-Down Clamp (optional accessory).

6.Make the cut, pull the workpiece back, turn the saw off, wait for Blade to stop and remove cut off piece

before continuing.

=

MITER cu'ri'ING

MITER CUTTING is known as cutting wood at an angle other than 90 ° with the edge of the wood. Follow the same procedure as you would for crosscutting.

Adjust the Miter Gauge to the desired angle, and lock it. The Miter Gauge may be used in either ofthe grooves in

the table.

When using the Miter Gauge in the LEFT hand groove,

hold the wo_ece firmly against the Miter Gauge head with your left hand, and gdp the Lock Handle with your

right.

Whenusing the RIGHThandgroove, holdthe workplece with your right hand and the Knob with your lefl hand.

Use the Hold-Down Clamp (optional accesson/) on the Miter Gauge for greater accuracy.

LEFT HAND REMOVED "\ FOR PICTURE CLARITY \

WORK SUPPORT

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Instructions Carefully Part No. SP5396Full ONE Year Warranty on Craftsman Table SAW Before Using the SAWWhen Installing or Moving the SAW Before Each USEWear Your Whenever SAW Blade is Spinning Kerfs about 5/16 ApartAdditional iNSTRUCTIONS for Before StartingBefore Leaving the SAW Turn the saw offGlossary of terms for woodworking Motor specifications and electrical requirementsConnecting to Power Source Outlet Contents Unpacking and checking contents AB AC AD AE Afag AH Part Name QTYFollowing items Spacer, Rip Fence Guide Bar Checking Blade Squareness to Installing HandwheelsChecking Table Insert Assembung Steel Legs Assembly Install screws, washers, Iockwashers and nuts as shownAttaching and Assembling Table Extensions ExternalHEX NUT Lock Washer Mounting Switch16-18 x 3/4 HEX Head Screw 2t/64 tN Washer Instalung Right Front RiP Fence Guide BAR 16-18 x 3/4HEX NU External Lockwasher HEX Head Screw 5116-18 x 3/4Flat Washer Rear Fence Guide BAR Bracket Extension7TH Slot 5TH Slot 1ST Slot HEX Head Screw 16-18 x 18THICKNESSES of Paper Self Aligning Spring Adjustment Aligning RiP FenceRiP Fence Alignment Adjustment Lockwash ER Adjusting RiP Scale PointerInstalling Blade Guard Assemby EmDOFRODMounting the Motor 16IN. WrenchMake Sure Keyis Removed from Shaft KEYInstalung Belt Positioning Motor on Motor Mounting BaseMounting Motor on Motor Base SetscrewInstalling Belt Guard SUPPO...ACKETPlugging iN Motor INSTALLiNG Belt GuardFrom among the loose parts find 2 Wire Ties Authorizedand Possible Hazardous USE by Children and Others ON-OFF SwitchSawblade Getting to know your saw Removing and iNSTALLiNG SawbladeEXACT-I-CUT Blade Guard not Shown For Picture Clarity Picture ClarifySafety instructions for basic saw operations Before Each USEWhenever SAW Blade is Spinning Work Helpers Safety for basic saw operationsBasic saw operation using the miter gauge Crosscutting Auxiliary Panel Work SupportYwood Parallel Plywood Auxiliary PANEL/WORK SupportBasic saw operation Repetitive CuttingMiter curiING RightUsing the rip fence ADDmONAL Safety Instructions forBevel Crosscutting Compound Miter CuttingUsing Featherboards for Thru Sawing RippingBevel RiPPiNG RESAWlNG HelpersCutting Panels RabbetingBack of SAW Using Featherboards for NON Thru SawingMolding Cutting Adjustments Miter GaugeFront Trunnion Rear Trunnion REAR-TRUNNION Screws Position Blade TILT, or Squareness of Blade to TableNut inside using a 3/8 inch wrench Ad ustmentsTilt Mechanism TeethMaintenance Sears recommends the following accessoriesTrouble Shooting General Troubleshooting MotorTrouble Probable Causeremedy Trouble Probable CauseTroubleshooting Motor Contd TroubleRepair parts =g$ Repair parts Page Parts LiST for Craftsman 10 Inch Table SAW Model 113.298721 KEY Part Description16-18 x 1-1t4 PARTs LiST for Craftsma 10 iNCH Table SAWKiey Part Description Repair Parts Parts List for Craftsman 10 Inch Table SAW Model !13.298721Guard Assembly LEG SET Hardware for Attaching Legs to SAWINCH Table SAW

298721, 113.298721, 113.298761 specifications

The Craftsman 298721, also known by its model numbers 113.298721 and 113.298761, represents a well-crafted power tool that has gained popularity among DIY enthusiasts and professionals alike. This versatile tool is designed to facilitate a variety of woodworking and construction tasks, making it an invaluable addition to any workshop.

One of the standout features of the Craftsman 298721 is its robust build quality. Crafted from durable materials, this tool is designed to withstand the rigors of heavy use. Its sturdy construction not only ensures longevity but also enhances user safety, as it can endure demanding tasks without compromising performance.

Equipped with a powerful motor, the Craftsman 298721 delivers consistent performance across various applications. The high horsepower ensures that it can easily handle tough materials, allowing users to make precise cuts and achieve desired outcomes effortlessly. The motor is also designed to operate quietly, mitigating the noise commonly associated with power tools and providing a more pleasant working environment.

Another notable characteristic is its user-friendly design. The tool features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended periods of use. This attention to ergonomics is evident in the lightweight build, making it easier for users to maneuver the tool with ease.

In terms of technology, the Craftsman 298721 incorporates advanced features that enhance its usability. One such feature is its adjustable speed control, allowing users to tailor the tool's performance to specific tasks. This adaptability makes it suitable for a wide range of applications, from intricate detail work to heavier cutting jobs.

The tool's compatibility with various attachments further extends its utility. Users can easily switch between different blades and accessories, enabling them to tackle diverse projects without the need for multiple tools. This flexibility makes the Craftsman 298721 a cost-effective solution for those looking to streamline their workshop.

Additionally, the safety mechanisms integrated into the Craftsman 298721 ensure that users can operate the tool confidently. Features such as blade guards and lock-off switches provide an extra layer of protection, reducing the risk of accidents while working.

In summary, the Craftsman 298721, alongside its model numbers 113.298721 and 113.298761, is a versatile and reliable power tool that combines robust construction, powerful performance, user-friendly features, and advanced technology. Whether for professional contractors or home improvement enthusiasts, this tool stands out as an essential asset for any workshop.
Top Page Image Contents