Craftsman 113.298721, 113.298761 Additional iNSTRUCTIONS for, Before Starting, Turn the saw off

Page 5

BEFORE STARTING

1.TO avoid kickbacks and slips into the blade, make sure the Rip Fence is parallel to the sawblade.

2.Check the anti-kickback pawls. (See "BASIC SAW OPERATION - USING THE RIP FENCE.") The Pawls must stop a kickback once it has started.

Replace or sharpen Anti-Kickback Pawls when points become dull.

3.Plastic and composition (like hardboard) materials may be cut on your saw. However, since these are usually quite hard and slippery, the Anti-Kickback Pawls may not stop a kickback. Therefore, be espe- cially careful in your set-up and cutting procedures.

WHILE CUTTING

1.To avoid kickbacks and slips into the blade, always push forward on the section of the wo rkpiece between the saw blade andthe Rip Fence. Never push forward on the piece being cut off.

ADDITIONAL iNSTRUCTIONS FOR

CROSSCUT TYPE CUTS

BEFORE STARTING

1.NEVER use the Rip Fence when crosscutting.

2.An auxiliary wood facing attached to the Miter Gauge can help prevent workpiece twisting and throwbacks. Attach itto the holes provided. Make the facing long enough and big enough to support your work. Make sure, however, it will not interfere with the Sawblade Guard. (See page 26)

3.Use jigs or fixtures to help hold any piece too small to extend across the full length of the Miter Gauge face during the cut. This lets you properly hold the Miter Gauge and workpiece and helps keep your hands away from the blade.

WHILE CUTTING

1.To avoid blade contact, always hold the Miter Gauge as shown in the "BASIC SAW OPERATIONS - US-

ING THE MITER GAUGE."

BEFORE LEAVING THE SAW

1.Turn the saw off.

2.Wait for blade to stop spinning.

3.Make workshop child-proof. Lock the shop. Discon- nect master switches. Remove the yellow Switch Key. Store _ away from children and others not qualified to use the tool.

4.Unplug the saw.

glossary of terms for woodworking

Anti-Kickback Pawls (AKP)

Device which, when properly maintained, is designed to stop the workpiece from being kicked back at the opera- tor during dpping operation.

Arbor

The shaft on which a cutting tool is mounted.

Crosscut

A cutting or shaping operation made across the width of the workpiece.

Dado

A non through cut which produces a square sided notch or trough in the workpiece.

Featherboard

A device which can help guide workpieces during rip type operation.

Freehand

Performing a cut without using a Fence, Miter Gauge, fixture, hold down or other proper device to keep the workpiece from twisting during the cut.

Gum

A sticky, sap based residue tram wood products. Heel

Misalignment of the blade.

Kerr

The amount of material removed by the blade in a through cut or the slot produced by the blade in a non through or partial cut.

Kickback

An uncontrolled grabbing and throwing of the workpiece back toward the front of the saw.

Leading End

The end of the workpiece which, during a rip type operation, is pushed into the cutting tool first.

Molding

Anon through cut which produces a special shape in the workpiece used for joining or decoration.

Push Stick

Adevice used to feed the workpiece through the saw during narrow ripping type operations and helps keep the operator'shands well away from the blade.

Push Block

Adevice used for ripping type operations too narrow to allow use of a Push Stick.

Rabbet

A notch in the edge of a workpiece.

Resin

A sticky, sap base substance that has hardened.

Ripping

Acutting operation along the length of the workpiece.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one minute.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Part No. SP5396 Instructions CarefullyBefore Using the SAW Full ONE Year Warranty on Craftsman Table SAWWhen Installing or Moving the SAW Before Each USEWear Your Kerfs about 5/16 Apart Whenever SAW Blade is SpinningBefore Starting Additional iNSTRUCTIONS forBefore Leaving the SAW Turn the saw offGlossary of terms for woodworking Motor specifications and electrical requirementsConnecting to Power Source Outlet Contents Unpacking and checking contents AB AC AD AE Afag AH Part Name QTYFollowing items Spacer, Rip Fence Guide Bar Checking Blade Squareness to Installing HandwheelsChecking Table Insert Assembung Steel Legs Install screws, washers, Iockwashers and nuts as shown AssemblyAttaching and Assembling Table Extensions ExternalHEX NUT Lock Washer Mounting Switch16-18 x 3/4 HEX Head Screw 2t/64 tN Washer 16-18 x 3/4 Instalung Right Front RiP Fence Guide BARHEX NU External Lockwasher HEX Head Screw 5116-18 x 3/4Rear Fence Guide BAR Bracket Extension Flat Washer7TH Slot 5TH Slot 1ST Slot HEX Head Screw 16-18 x 18THICKNESSES of Paper Aligning RiP Fence Self Aligning Spring AdjustmentRiP Fence Alignment Adjustment Lockwash ER Adjusting RiP Scale PointerInstalling Blade Guard EmDOFROD Assemby16IN. Wrench Mounting the MotorMake Sure Keyis Removed from Shaft KEYPositioning Motor on Motor Mounting Base Instalung BeltMounting Motor on Motor Base SetscrewSUPPO...ACKET Installing Belt GuardPlugging iN Motor INSTALLiNG Belt GuardFrom among the loose parts find 2 Wire Ties Authorizedand Possible Hazardous USE by Children and Others ON-OFF SwitchSawblade Getting to know your saw Sawblade Removing and iNSTALLiNGEXACT-I-CUT Blade Guard not Shown For Picture Clarity Picture ClarifyBefore Each USE Safety instructions for basic saw operationsWhenever SAW Blade is Spinning Work Helpers Safety for basic saw operationsBasic saw operation using the miter gauge Auxiliary Panel Work Support CrosscuttingYwood Parallel Plywood Auxiliary PANEL/WORK SupportRepetitive Cutting Basic saw operationMiter curiING RightADDmONAL Safety Instructions for Using the rip fenceBevel Crosscutting Compound Miter CuttingRipping Using Featherboards for Thru SawingBevel RiPPiNG Helpers RESAWlNGRabbeting Cutting PanelsBack of SAW Using Featherboards for NON Thru SawingMolding Cutting Miter Gauge AdjustmentsFront Trunnion Rear Trunnion REAR-TRUNNION Screws Blade TILT, or Squareness of Blade to Table PositionAd ustments Nut inside using a 3/8 inch wrenchTilt Mechanism TeethSears recommends the following accessories MaintenanceTroubleshooting Motor Trouble Shooting GeneralTrouble Probable Causeremedy Trouble Probable CauseTrouble Troubleshooting Motor ContdRepair parts =g$ Repair parts Page KEY Part Description Parts LiST for Craftsman 10 Inch Table SAW Model 113.29872116-18 x 1-1t4 PARTs LiST for Craftsma 10 iNCH Table SAWKiey Part Description Repair Parts Model !13.298721 Parts List for Craftsman 10 Inch Table SAWGuard Assembly Hardware for Attaching Legs to SAW LEG SETINCH Table SAW

298721, 113.298721, 113.298761 specifications

The Craftsman 298721, also known by its model numbers 113.298721 and 113.298761, represents a well-crafted power tool that has gained popularity among DIY enthusiasts and professionals alike. This versatile tool is designed to facilitate a variety of woodworking and construction tasks, making it an invaluable addition to any workshop.

One of the standout features of the Craftsman 298721 is its robust build quality. Crafted from durable materials, this tool is designed to withstand the rigors of heavy use. Its sturdy construction not only ensures longevity but also enhances user safety, as it can endure demanding tasks without compromising performance.

Equipped with a powerful motor, the Craftsman 298721 delivers consistent performance across various applications. The high horsepower ensures that it can easily handle tough materials, allowing users to make precise cuts and achieve desired outcomes effortlessly. The motor is also designed to operate quietly, mitigating the noise commonly associated with power tools and providing a more pleasant working environment.

Another notable characteristic is its user-friendly design. The tool features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended periods of use. This attention to ergonomics is evident in the lightweight build, making it easier for users to maneuver the tool with ease.

In terms of technology, the Craftsman 298721 incorporates advanced features that enhance its usability. One such feature is its adjustable speed control, allowing users to tailor the tool's performance to specific tasks. This adaptability makes it suitable for a wide range of applications, from intricate detail work to heavier cutting jobs.

The tool's compatibility with various attachments further extends its utility. Users can easily switch between different blades and accessories, enabling them to tackle diverse projects without the need for multiple tools. This flexibility makes the Craftsman 298721 a cost-effective solution for those looking to streamline their workshop.

Additionally, the safety mechanisms integrated into the Craftsman 298721 ensure that users can operate the tool confidently. Features such as blade guards and lock-off switches provide an extra layer of protection, reducing the risk of accidents while working.

In summary, the Craftsman 298721, alongside its model numbers 113.298721 and 113.298761, is a versatile and reliable power tool that combines robust construction, powerful performance, user-friendly features, and advanced technology. Whether for professional contractors or home improvement enthusiasts, this tool stands out as an essential asset for any workshop.
Top Page Image Contents