Using the rip fence

BEVEL CROSSCUTTING

BEVEL CROSSCUTTING is the same as crosscutting

except that the wood is also cut at an angle, other than 90° with the flat side of the wood.

Adjust the blade to the desired angle.

Use the Miter Gauge in the groove to the RIGHT of the blade. It cannot be used in the groove to the LEFT because the Blade Guard will interfere. Hold the work-

piece with your right hand and the Lock Handle with your left hand.

Use the Auxiliary FenceNVork Support for additional support of the workpiece,

Lay itacross the Guide Bars to support the workpiece as near to the end as possible,

Use the Hold-Down Clamp (optional accessory) on the Miter Gauge for greater accuracy.

COMPOUND MITER CUTTING

COMPOUND MITER CUTTING is a combination of miter cutting and bevel crosscutting. The cut is made at

an angle other than 90 ° to boththe edge and the flat side of the wood.

Adjust the Miter Gauge and the blade to the desired angle. Make sure Miter Gauge is locked.

RIPPING, BEVEL RIPPING, RESAWlNG AND RAB- BETING are performed using the RIP FENCE together with the AUXILIARY FENCE/WORK SUPPORT, PUSH STICK OR PUSH BLOCK.

WARNING: Foryourown safety, always observe the following safety precautions in addition to the safety instructions on pages 2, 3, 4, 5, 28, 29 & 30.

ADDmONAL SAFETY INSTRUCTIONS FOR

RiP TYPE CUTS

1.NEVER use the Miter Gauge when ripping.

2.Use a Push Stick whenever the fence is 2 or more inches from the blade. When thru-sawing, use an

Auxiliary Fence and Push Biockwhenever the Fence must be between 1/2 inch and 2 inches of the blade.

Never thru-saw ripcuts less than 1/2 inchwide.

3.When using a Push Stick or Push Block, the trailing end of the board must be square. A Push Stick or Block againstan uneven end could slipoff or push the work away from the fence.

4.Never rip anything shorter than 10 inches long.

5. A FEATHERBOARD can help guide the workpiece.

KERFS ABOUT

5/16" APART

4-1/'

Before staring:

1.To avoid kickbacks and slips into the blade, make sure the Rip Fence is parallel to the sawblade,

2.Check the Anti-Kickback Pawls. The Pawls must stop a kickback once it has started. Replace or

sharpen Anti-Kickback Pawls when points become dull.

3.Plastic and composition (like hardboard) materials may be cut on your saw. However, since these are usually quite hard and slippery, the Anti-KickbackPawls may not stop a kickback. Therefore, be espe- cially careful in your set-upand cutting procedures.

While cutting:

1.To avoid kickbacks and slips into the blade, a_ways push forward on the section of the wo rkpiece between the saw blade and the Rip Fence. Never pushforward on the piece being cut off.

298721, 113.298721, 113.298761 specifications

The Craftsman 298721, also known by its model numbers 113.298721 and 113.298761, represents a well-crafted power tool that has gained popularity among DIY enthusiasts and professionals alike. This versatile tool is designed to facilitate a variety of woodworking and construction tasks, making it an invaluable addition to any workshop.

One of the standout features of the Craftsman 298721 is its robust build quality. Crafted from durable materials, this tool is designed to withstand the rigors of heavy use. Its sturdy construction not only ensures longevity but also enhances user safety, as it can endure demanding tasks without compromising performance.

Equipped with a powerful motor, the Craftsman 298721 delivers consistent performance across various applications. The high horsepower ensures that it can easily handle tough materials, allowing users to make precise cuts and achieve desired outcomes effortlessly. The motor is also designed to operate quietly, mitigating the noise commonly associated with power tools and providing a more pleasant working environment.

Another notable characteristic is its user-friendly design. The tool features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended periods of use. This attention to ergonomics is evident in the lightweight build, making it easier for users to maneuver the tool with ease.

In terms of technology, the Craftsman 298721 incorporates advanced features that enhance its usability. One such feature is its adjustable speed control, allowing users to tailor the tool's performance to specific tasks. This adaptability makes it suitable for a wide range of applications, from intricate detail work to heavier cutting jobs.

The tool's compatibility with various attachments further extends its utility. Users can easily switch between different blades and accessories, enabling them to tackle diverse projects without the need for multiple tools. This flexibility makes the Craftsman 298721 a cost-effective solution for those looking to streamline their workshop.

Additionally, the safety mechanisms integrated into the Craftsman 298721 ensure that users can operate the tool confidently. Features such as blade guards and lock-off switches provide an extra layer of protection, reducing the risk of accidents while working.

In summary, the Craftsman 298721, alongside its model numbers 113.298721 and 113.298761, is a versatile and reliable power tool that combines robust construction, powerful performance, user-friendly features, and advanced technology. Whether for professional contractors or home improvement enthusiasts, this tool stands out as an essential asset for any workshop.