Craftsman 113.298721, 113.298761 manual Mounting the Motor, 16IN. Wrench, Key, DIA, Shaft

Page 21

15.IMPORTANT: To work properly, the Spreader must always be PARALLEL to the sawblade and adjusted so the cut workplece will pass on either side at the Spreader without binding or skewing to the side.

NOTE: The Spreader is thinner than the width of the cut (KERF) by approximately six thicknesses of paper.

16.Make two folds in a small piece (6 x 6 inch)of ordinary NEWSPAPER making three thicknesses.

The folded paper will be used as a "spacing gauge".

17.Place RipFence on table, CAREFULLY move it against blade so that it is parallel to the blade, and

just TOUCHEStips of sawteeth. Tighten Rip Fence Lock Lever.

18. Insert folded paper between Spreader and Fence.

19.Using 7/16 wrench loosen the 1/4-20 hex head screws so the Spreader can slide sideways.

20.Hold Spreader flat against Fence. Tighten screws using 7/16 inch wrench.

21.To remove Blade Guard and Spreader, loosen Thumbscrew. DO NOT LOOSEN OTHER SCREWS.

This lets you remove and replace the Guard without disturbing the Spreader alignment.

KERF WOOD

SPREADER

..__ --

. ....

LOOKING DOWN ON SAW

/

FOLDED PAPER

7/16IN. WRENCH

MOUNTING THE MOTOR

Model 113.298721 & 113.298761

Check Motor Rotation

1.The Motor must rotate CLOCKWISE when viewed from the 5/8 inch shaft.

2.MAKE SURE "KEY'IS REMOVED FROM SHAFT.

3.Place the Motor on your workbench or on the floor.

4.Plug the cord into a properly grounded outlet (See

"MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS" section) Notice the rotation of the shaft. If it is not turning CLOCKWISE, do not assemble or attempt to operate saw until motor with correct rotation is obtained,

KEY

TION

518IN.

DIA, SHAFT

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Part No. SP5396 Instructions CarefullyBefore Using the SAW Full ONE Year Warranty on Craftsman Table SAWWhen Installing or Moving the SAW Before Each USEWear Your Kerfs about 5/16 Apart Whenever SAW Blade is SpinningBefore Starting Additional iNSTRUCTIONS forBefore Leaving the SAW Turn the saw offMotor specifications and electrical requirements Connecting to Power Source OutletGlossary of terms for woodworking Contents Unpacking and checking contents Part Name QTY Following items Spacer, Rip Fence Guide BarAB AC AD AE Afag AH Installing Handwheels Checking Table InsertChecking Blade Squareness to Assembung Steel Legs Install screws, washers, Iockwashers and nuts as shown AssemblyAttaching and Assembling Table Extensions ExternalMounting Switch 16-18 x 3/4 HEX Head Screw 2t/64 tN WasherHEX NUT Lock Washer 16-18 x 3/4 Instalung Right Front RiP Fence Guide BARHEX NU External Lockwasher HEX Head Screw 5116-18 x 3/4Rear Fence Guide BAR Bracket Extension Flat Washer7TH Slot 5TH Slot 1ST Slot HEX Head Screw 16-18 x 18THICKNESSES of Paper Aligning RiP Fence Self Aligning Spring AdjustmentRiP Fence Alignment Adjustment Adjusting RiP Scale Pointer Installing Blade GuardLockwash ER EmDOFROD Assemby16IN. Wrench Mounting the MotorMake Sure Keyis Removed from Shaft KEYPositioning Motor on Motor Mounting Base Instalung BeltMounting Motor on Motor Base SetscrewSUPPO...ACKET Installing Belt GuardINSTALLiNG Belt Guard From among the loose parts find 2 Wire TiesPlugging iN Motor ON-OFF Switch SawbladeAuthorizedand Possible Hazardous USE by Children and Others Getting to know your saw Sawblade Removing and iNSTALLiNGEXACT-I-CUT Blade Guard not Shown For Picture Clarity Picture ClarifyBefore Each USE Safety instructions for basic saw operationsWhenever SAW Blade is Spinning Safety for basic saw operations Basic saw operation using the miter gaugeWork Helpers Auxiliary Panel Work Support CrosscuttingYwood Parallel Plywood Auxiliary PANEL/WORK SupportRepetitive Cutting Basic saw operationMiter curiING RightADDmONAL Safety Instructions for Using the rip fenceBevel Crosscutting Compound Miter CuttingRipping Using Featherboards for Thru SawingBevel RiPPiNG Helpers RESAWlNGRabbeting Cutting PanelsUsing Featherboards for NON Thru Sawing Molding CuttingBack of SAW Miter Gauge AdjustmentsFront Trunnion Rear Trunnion REAR-TRUNNION Screws Blade TILT, or Squareness of Blade to Table PositionAd ustments Nut inside using a 3/8 inch wrenchTilt Mechanism TeethSears recommends the following accessories MaintenanceTroubleshooting Motor Trouble Shooting GeneralTrouble Probable Causeremedy Trouble Probable CauseTrouble Troubleshooting Motor ContdRepair parts =g$ Repair parts Page KEY Part Description Parts LiST for Craftsman 10 Inch Table SAW Model 113.298721PARTs LiST for Craftsma 10 iNCH Table SAW Kiey Part Description16-18 x 1-1t4 Repair Parts Model !13.298721 Parts List for Craftsman 10 Inch Table SAWGuard Assembly Hardware for Attaching Legs to SAW LEG SETINCH Table SAW

298721, 113.298721, 113.298761 specifications

The Craftsman 298721, also known by its model numbers 113.298721 and 113.298761, represents a well-crafted power tool that has gained popularity among DIY enthusiasts and professionals alike. This versatile tool is designed to facilitate a variety of woodworking and construction tasks, making it an invaluable addition to any workshop.

One of the standout features of the Craftsman 298721 is its robust build quality. Crafted from durable materials, this tool is designed to withstand the rigors of heavy use. Its sturdy construction not only ensures longevity but also enhances user safety, as it can endure demanding tasks without compromising performance.

Equipped with a powerful motor, the Craftsman 298721 delivers consistent performance across various applications. The high horsepower ensures that it can easily handle tough materials, allowing users to make precise cuts and achieve desired outcomes effortlessly. The motor is also designed to operate quietly, mitigating the noise commonly associated with power tools and providing a more pleasant working environment.

Another notable characteristic is its user-friendly design. The tool features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended periods of use. This attention to ergonomics is evident in the lightweight build, making it easier for users to maneuver the tool with ease.

In terms of technology, the Craftsman 298721 incorporates advanced features that enhance its usability. One such feature is its adjustable speed control, allowing users to tailor the tool's performance to specific tasks. This adaptability makes it suitable for a wide range of applications, from intricate detail work to heavier cutting jobs.

The tool's compatibility with various attachments further extends its utility. Users can easily switch between different blades and accessories, enabling them to tackle diverse projects without the need for multiple tools. This flexibility makes the Craftsman 298721 a cost-effective solution for those looking to streamline their workshop.

Additionally, the safety mechanisms integrated into the Craftsman 298721 ensure that users can operate the tool confidently. Features such as blade guards and lock-off switches provide an extra layer of protection, reducing the risk of accidents while working.

In summary, the Craftsman 298721, alongside its model numbers 113.298721 and 113.298761, is a versatile and reliable power tool that combines robust construction, powerful performance, user-friendly features, and advanced technology. Whether for professional contractors or home improvement enthusiasts, this tool stands out as an essential asset for any workshop.
Top Page Image Contents