Craftsman 137.21237 Estimated Assembly Time 5 10 minutes, Unlocking the Slide Carriage FIG. B

Page 10

Estimated Assembly Time: 5 - 10 minutes

[,AWAR"I"G

To avoid injury, do not connect this miter saw to the power source until it is completely assembled and adjusted and you have read and understood this

Operator's Manual.

iNSTALLiNG THE MITER HANDLE (FIG. A)

1Thread the miter handle (1) into the hole located at the front of the miter table.

Fig. A

UNLOCKING THE SLIDE CARRIAGE (FIG. B)

After removing the saw from the carton, loosen the slide carriage lock knob (1). When transporting or storing the miter saw, the slide carriage should always be locked in position. The slide carriage lock knob (1) is located on the bottom of the slide carriage.

Fig. B

SAW BLADE WRENCH (FIG. B-l)

1.For convenient storage and prevention of loss, there is a slot (1) in the rear of the carrying handle (2) for storing the blade wrench (3) when not in use.

Fig. B-1

3

I

2

 

 

CUTTING HEAD (FIG. C)

Raising

1.Push down slightly on the switch handle (I).

2.Pull out the stop latch knob (2).

3.Allow the cutting head to rise to the up position.

IA WARNING

To avoid injury and damage to the saw, transport and store the miter saw with the cutting head locked in the down position. Never use the stop latch to hold the cutting head in a down position for cutting operations.

Fig, C

Locking

When transporting or storing the miter saw, the cutting head should always be locked in the down position.

1.Push the cutting head down to its lowest position.

2.Push the stop latch knob (2) into the locking hole. IMPORTANT: To avoid damage, never carry the miter saw by the switch handle, the cutting arm or the miter handle. ALWAYS use the designated carrying handle.

iNSTALLiNG THE DUST BAG (FIG. D)

1.Squeeze the metal collar wings (2) of the dust bag (1).

2.Place the dust bag neck opening around the exhaust port (3), and release the metal collar wings.

Fig. D

I2

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents CRSFrSMSN Model NoBlade Ection PAG E SectionMotor Miter SAW Rotating TableUSE Proper Extension CORDS. Make sure Disconnect Tools from Power SourceCheck for Damaged PARTS. Check for Keep the Motor AIR Slots Clean and free of chips or dust Power Supply and Motor SpecificationsMotor Safety Protection Double InsulatedIL Warning Recommended AccessoriesAccessories Combination Square Must be TrueIA Warning Unpacking Your Miter SAWPage Woodworking Terms Unlocking the Slide Carriage FIG. B Estimated Assembly Time 5 10 minutesINSTALLiNG the Dust BAG FIG. D RaisingIAWARNmNG INSTALLiNG the HOLD-DOWN ClampWARNINe Mounting the Miter SAW FIG. G, G=IRemoving and Installing the Blade MountinginstructionsFrom turning the machine on Laser Guide FIG. KAvoid Direct EYE Contact Bevel Stop Adjustment Bevel Adjustment Fig. NMiter Scale Indicator Adjustment FIG. O Miter Angle Adjustment FIG. OSetting Cutting Depth FIG. Q Adjusting Fence Squareness FIG. PRecommended Accessories Before Using the Miter SAWSafety and Operations Sections Keep Your Work Area CleanPlan Your Work Dress for SafetyWhen SAW is Running Do not OverreachBody and Hand Position FIG. R Before freeing jammed material 6 Release trigger switchIAWARNmNO To Turn SAW on FIG. SBefore Leaving the SAW WAR.mr,JGISliding Carriage System FIG Miter CUT FIG. UCompound CUT FIG IAWANiGIBevel Stop for Crown Molding FIG. W Slide Cutting Wide Boards UP to 12 in. WideCutting Bowed Material FIG. Z Auxiliary Wood Fence FIG. CCCutting Crown Molding FIG. EE, FF Bevel/Miter SettingsCuttingbasemolding FIG. DD Inside corner-Left sideCrown Molding Chart AWARmG MaintenanceIAwARJG Problem Cause Suggested Corrective Action Problem Problem Cause Suggested Corrective ActionParts List for SAW Schematic 10INSUDINGCOMPOUNDMtTESAW.MODEL.O137.212370Schematic for SAW Parts List and Schematic for Motor SAW ModelPage Your Home

137.21237 specifications

The Craftsman 137.21237 table saw is a versatile and robust woodworking tool that caters to both amateur and professional woodworkers. Renowned for its reliability and precision, this table saw has made a mark in the DIY community and among seasoned craftspeople alike.

One of the standout features of the Craftsman 137.21237 is its powerful motor. With a 15-amp motor, it provides ample power to tackle a variety of cutting tasks. This motor facilitates smooth cuts through hardwoods and thick materials, ensuring that users experience consistent performance without lag. The saw comes equipped with a 10-inch blade that spins at impressive RPMs, allowing for clean, efficient cuts across different types of wood and plywood.

Another key characteristic of this table saw is its durable construction. The table surface is made of cast iron, providing a stable base that minimizes vibrations during operation. This stability is crucial for achieving accuracy in cuts, especially for intricate projects that require precise measurements. The table itself measures a generous size, allowing for larger workpieces to be cut with ease.

The Craftsman 137.21237 also boasts an advanced rip fence system. The fence is designed for quick adjustments, enabling users to make straight, consistent cuts at various widths. The easy locking mechanism ensures that your settings remain in place while cutting, enhancing safety and accuracy.

Safety is a paramount concern with the Craftsman 137.21237. It features an integrated blade guard, which provides protection against accidental contact with the blade. Additionally, the saw includes riving knife technology, which helps prevent kickback by keeping the wood aligned during cuts. This safety technology is crucial for woodworkers looking to minimize risk while operating powerful equipment.

Portability is another important aspect of the Craftsman 137.21237. Despite its sturdy build, the saw is designed with user convenience in mind. It includes onboard storage for accessories and additional parts, as well as a foldable stand, making it easy to transport and store when not in use.

In summary, the Craftsman 137.21237 table saw combines power, durability, and precision. With its strong 15-amp motor, robust cast iron construction, advanced safety features, and user-friendly design, it stands out as a reliable choice for anyone engaged in woodworking projects. Whether you're building furniture, crafting cabinetry, or undertaking home improvement tasks, this table saw provides the functionality and performance that can enhance your woodworking experience.
Top Page Image Contents