Craftsman 137.21237 operating instructions Mountinginstructions, Removing and Installing the Blade

Page 12

Mountinginstructions

1.For stationary use, place the saw in the desired location, directly on a workbench where there is room for handling and proper support of the workpiece.

The base of the saw has four mounting holes. Bolt the base of the miter saw (1) to the work surface (5), using the fastening method as shown in Fig G.

Fig. G

2.Hex head bolt 3

1.Miter saw base 2

3.

Rubber washer

4

,,

4.

Flat washer

1

_

5.

Workbench

 

_ I

 

 

 

I 1

6.

Flat washer

5

_

7.Lockwasher

 

 

 

8

9.

Jam nut

_

9

8.

Hex nut

NOTE: Mounting hardware is not included with this tool. Bolts, nuts, washers and screws must be purchased separately.

2.For portable use, place the saw on a 3/4 in. thick piece of plywood. Bolt the base of the miter saw securely to the plywood using the mounting holes on the base. Use C-clamps to clamp this mounting board to a stable work surface at the worksite. (Fig. G-1 )

Fig.G-1

REMOVING AND INSTALLING THE BLADE

WARNING]

Do not use a blade larger than 10 in. in diameter.

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outmet.

Removing Blade (Fig. H, I and J)

1.Unplug the saw from the outlet.

2.Allow the cutting head to rise to the upright position. Raise the lower blade guard (1) to the up position.

3.Loosen the cover plate screw (2) with a Phillips screwdriver.

4.Rotate the cover plate (3) towards the rear of the tool to expose the arbor bolt (4).

5.Place the blade wrench over the arbor bolt.

Fig.H

3

2

4

//

. Locate the arbor lock (5) on the motor, below the switch handle. (Fig. I)

7.Press the arbor lock, holding it in firmly while turning the blade wrench clockwise. The arbor lock will

engage after turning the wrench. Continue to hold the arbor locking to keep it engaged, while turning the wrench clockwise to loosen the arbor bolt.

Fig.I

5

8.Remove the arbor bolt (6), the outer blade collar (8) and the blade (7). Do not remove the inner blade coltar. (Fig. J)

NOTE: Pay attention to the pieces removed, noting their position and direction they face. Wipe the blade collars clean of any sawdust before installing a new blade.

Fig. J

8 7

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents CRSFrSMSN Model NoEction PAG E Section Motor Miter SAWBlade Rotating TableDisconnect Tools from Power Source USE Proper Extension CORDS. Make sureCheck for Damaged PARTS. Check for Keep the Motor AIR Slots Clean and free of chips or dust Power Supply and Motor SpecificationsMotor Safety Protection Double InsulatedRecommended Accessories AccessoriesIL Warning Combination Square Must be TrueIA Warning Unpacking Your Miter SAWPage Woodworking Terms Estimated Assembly Time 5 10 minutes INSTALLiNG the Dust BAG FIG. DUnlocking the Slide Carriage FIG. B RaisingINSTALLiNG the HOLD-DOWN Clamp WARNINeIAWARNmNG Mounting the Miter SAW FIG. G, G=IRemoving and Installing the Blade MountinginstructionsLaser Guide FIG. K From turning the machine onAvoid Direct EYE Contact Bevel Stop Adjustment Bevel Adjustment Fig. NMiter Angle Adjustment FIG. O Setting Cutting Depth FIG. QMiter Scale Indicator Adjustment FIG. O Adjusting Fence Squareness FIG. PBefore Using the Miter SAW Safety and Operations SectionsRecommended Accessories Keep Your Work Area CleanDress for Safety When SAW is RunningPlan Your Work Do not OverreachBefore freeing jammed material 6 Release trigger switch IAWARNmNOBody and Hand Position FIG. R To Turn SAW on FIG. SWAR.mr,JGI Sliding Carriage System FIGBefore Leaving the SAW Miter CUT FIG. UIAWANiGI Bevel Stop for Crown Molding FIG. WCompound CUT FIG Slide Cutting Wide Boards UP to 12 in. WideCutting Bowed Material FIG. Z Auxiliary Wood Fence FIG. CCBevel/Miter Settings Cuttingbasemolding FIG. DDCutting Crown Molding FIG. EE, FF Inside corner-Left sideCrown Molding Chart Maintenance AWARmGIAwARJG Problem Cause Suggested Corrective Action Problem Problem Cause Suggested Corrective ActionParts List for SAW Schematic 10INSUDINGCOMPOUNDMtTESAW.MODEL.O137.212370Schematic for SAW Parts List and Schematic for Motor SAW ModelPage Your Home

137.21237 specifications

The Craftsman 137.21237 table saw is a versatile and robust woodworking tool that caters to both amateur and professional woodworkers. Renowned for its reliability and precision, this table saw has made a mark in the DIY community and among seasoned craftspeople alike.

One of the standout features of the Craftsman 137.21237 is its powerful motor. With a 15-amp motor, it provides ample power to tackle a variety of cutting tasks. This motor facilitates smooth cuts through hardwoods and thick materials, ensuring that users experience consistent performance without lag. The saw comes equipped with a 10-inch blade that spins at impressive RPMs, allowing for clean, efficient cuts across different types of wood and plywood.

Another key characteristic of this table saw is its durable construction. The table surface is made of cast iron, providing a stable base that minimizes vibrations during operation. This stability is crucial for achieving accuracy in cuts, especially for intricate projects that require precise measurements. The table itself measures a generous size, allowing for larger workpieces to be cut with ease.

The Craftsman 137.21237 also boasts an advanced rip fence system. The fence is designed for quick adjustments, enabling users to make straight, consistent cuts at various widths. The easy locking mechanism ensures that your settings remain in place while cutting, enhancing safety and accuracy.

Safety is a paramount concern with the Craftsman 137.21237. It features an integrated blade guard, which provides protection against accidental contact with the blade. Additionally, the saw includes riving knife technology, which helps prevent kickback by keeping the wood aligned during cuts. This safety technology is crucial for woodworkers looking to minimize risk while operating powerful equipment.

Portability is another important aspect of the Craftsman 137.21237. Despite its sturdy build, the saw is designed with user convenience in mind. It includes onboard storage for accessories and additional parts, as well as a foldable stand, making it easy to transport and store when not in use.

In summary, the Craftsman 137.21237 table saw combines power, durability, and precision. With its strong 15-amp motor, robust cast iron construction, advanced safety features, and user-friendly design, it stands out as a reliable choice for anyone engaged in woodworking projects. Whether you're building furniture, crafting cabinetry, or undertaking home improvement tasks, this table saw provides the functionality and performance that can enhance your woodworking experience.
Top Page Image Contents