Craftsman 137.21237 operating instructions WARNINe, IAWARNmNG, INSTALLiNG the HOLD-DOWN Clamp

Page 11

iNSTALLiNG THE HOLD-DOWN CLAMP

(FIG. E and E-l)

I.Place the hold=down clamp assembly (1) in one of the mounting holes (2).

NOTE: There are no screws to secure clamp. The clamp will secure itself to the base when turning the knob (3) to clamp the workpiece. Do not use your other hand to hold the clamp when tightening. Only turn knob (3) to secure clamp to table. The clamp will tilt at an angle and secure itself when tightened_

[A WARNING

When using stop block on the right side, hold-down clamp must also be in right side. Using hold-down clamp on the Deftside during this operation can cause kickback and serious injury to the operator.

!

Fig. E

1.To remove, loosen and remove the six screws (1)

on the table insert (2) with a Phillips screwdriver and remove the insert.

2.To install, reposition the table insert, install the six screws and tighten.

3.Check for blade clearance by moving the slide carriage through the full motion of the blade in the table slot.

Fig. F

II

ii i

Fig. E-1 2

J_

\_._/2

2

REMOVING AND iNSTALLiNG THE TABLE INSERT

(FIG. F)

[A wARNINe!

To avoid injury:

,= Always unplug the saw to avoid accidental starting. Remove all small pieces of material from the table cavity before performing any cuts. The table insert may be removed for this purpose, but always reattach the table insert prior to performing a cutting operation.

•Do not start the sliding compound miter saw without checking for interference between the blade and table insert. Damage could result to the blade, table insert or turntable if blade strike occurs during the cutting operation.

MOUNTING THE MITER SAW (FIG. G, G=I)

IAWARNmNG

To avoid injury form unexpected saw movement:

=Disconnect the power cord from the outlet, and

lock the cutting head in the lower position using the stop latch.

eLock the slide carriage in place by tightening the

slide carriage lock knob.

=To avoid back injury, lift the saw by using the designated carrying handles located on the top of the machine. When lifting, bend at your knees,

not from your back.

•Never carry the miter saw by the power cord or by the switch handle. Carrying the tool by the power cord could cause damage to the insulation or the wire connections resulting in electric shock or fire.

=To avoid injury from flying debris, do not allow visitors to stand near the saw during any cutting operation.

=Support the saw on a level work surface.

=Bolt or clamp the saw to its support.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model No CRSFrSMSNRotating Table Ection PAG E SectionMotor Miter SAW BladeCheck for Damaged PARTS. Check for Disconnect Tools from Power SourceUSE Proper Extension CORDS. Make sure Power Supply and Motor Specifications Keep the Motor AIR Slots Clean and free of chips or dustDouble Insulated Motor Safety ProtectionCombination Square Must be True Recommended AccessoriesAccessories IL WarningUnpacking Your Miter SAW IA WarningPage Woodworking Terms Raising Estimated Assembly Time 5 10 minutesINSTALLiNG the Dust BAG FIG. D Unlocking the Slide Carriage FIG. BMounting the Miter SAW FIG. G, G=I INSTALLiNG the HOLD-DOWN ClampWARNINe IAWARNmNGMountinginstructions Removing and Installing the BladeAvoid Direct EYE Contact Laser Guide FIG. KFrom turning the machine on Bevel Adjustment Fig. N Bevel Stop AdjustmentAdjusting Fence Squareness FIG. P Miter Angle Adjustment FIG. OSetting Cutting Depth FIG. Q Miter Scale Indicator Adjustment FIG. OKeep Your Work Area Clean Before Using the Miter SAWSafety and Operations Sections Recommended AccessoriesDo not Overreach Dress for SafetyWhen SAW is Running Plan Your WorkTo Turn SAW on FIG. S Before freeing jammed material 6 Release trigger switchIAWARNmNO Body and Hand Position FIG. RMiter CUT FIG. U WAR.mr,JGISliding Carriage System FIG Before Leaving the SAWSlide Cutting Wide Boards UP to 12 in. Wide IAWANiGIBevel Stop for Crown Molding FIG. W Compound CUT FIGAuxiliary Wood Fence FIG. CC Cutting Bowed Material FIG. ZInside corner-Left side Bevel/Miter SettingsCuttingbasemolding FIG. DD Cutting Crown Molding FIG. EE, FFCrown Molding Chart IAwARJG MaintenanceAWARmG Problem Problem Cause Suggested Corrective Action Problem Cause Suggested Corrective Action10INSUDINGCOMPOUNDMtTESAW.MODEL.O137.212370 Parts List for SAW SchematicSchematic for SAW SAW Model Parts List and Schematic for MotorPage Your Home

137.21237 specifications

The Craftsman 137.21237 table saw is a versatile and robust woodworking tool that caters to both amateur and professional woodworkers. Renowned for its reliability and precision, this table saw has made a mark in the DIY community and among seasoned craftspeople alike.

One of the standout features of the Craftsman 137.21237 is its powerful motor. With a 15-amp motor, it provides ample power to tackle a variety of cutting tasks. This motor facilitates smooth cuts through hardwoods and thick materials, ensuring that users experience consistent performance without lag. The saw comes equipped with a 10-inch blade that spins at impressive RPMs, allowing for clean, efficient cuts across different types of wood and plywood.

Another key characteristic of this table saw is its durable construction. The table surface is made of cast iron, providing a stable base that minimizes vibrations during operation. This stability is crucial for achieving accuracy in cuts, especially for intricate projects that require precise measurements. The table itself measures a generous size, allowing for larger workpieces to be cut with ease.

The Craftsman 137.21237 also boasts an advanced rip fence system. The fence is designed for quick adjustments, enabling users to make straight, consistent cuts at various widths. The easy locking mechanism ensures that your settings remain in place while cutting, enhancing safety and accuracy.

Safety is a paramount concern with the Craftsman 137.21237. It features an integrated blade guard, which provides protection against accidental contact with the blade. Additionally, the saw includes riving knife technology, which helps prevent kickback by keeping the wood aligned during cuts. This safety technology is crucial for woodworkers looking to minimize risk while operating powerful equipment.

Portability is another important aspect of the Craftsman 137.21237. Despite its sturdy build, the saw is designed with user convenience in mind. It includes onboard storage for accessories and additional parts, as well as a foldable stand, making it easy to transport and store when not in use.

In summary, the Craftsman 137.21237 table saw combines power, durability, and precision. With its strong 15-amp motor, robust cast iron construction, advanced safety features, and user-friendly design, it stands out as a reliable choice for anyone engaged in woodworking projects. Whether you're building furniture, crafting cabinetry, or undertaking home improvement tasks, this table saw provides the functionality and performance that can enhance your woodworking experience.
Top Page Image Contents