Craftsman 137.21237 operating instructions Bevel Stop Adjustment, Bevel Adjustment Fig. N

Page 14

BEVEL STOP ADJUSTMENT

[4 WARNNNGI

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

90 ° (0 °) Bevel adjustment (Fig. L)

I.Loosen bevel lock handle (1) and tilt the cutting arm completely to the right. Tighten the bevel lock handle.

2.Place a combination square (2) on the miter table with the ruler against the table and the heel of the square against the saw blade.

3.If the blade is not 90 ° (0°) square with the miter table (5), loosen the bevel lock handle (I), tilt the cutting head to the left, loosen the Iocknut (4) on the bevel angle adjustment bolt (3) and use a 10 mm

wrench to adjust the stop bolt (3) depth in or out to increase or decrease the bevel angle.

4Tilt the cutting arm to back to the right at 90 _'(0°) bevel and recheck for alignment.

5.Repeat steps 1 through 4 if further adjustment is needed.

6Tighten bevel lock handle (1) and Iocknut (4) when alignment is achieved.

Fig. L

1

52

90 ° Bevel Pointer Adjustment (Fig. M)

1.When the blade is exactly 90 °`(0°) to the table, loosen

the bevel indicator screw (5) using a # 2 Phillips screwdriver.

2.Adjust bevel indicator (6) to the "0" mark on the bevel scale and retighten the screw.

Fig. M

y

5

6

45 ° Bevel Adjustment (Fig. N)

1.Loosen the bevel lock handle (7) and tilt the cutting head completely to the left.

2.Using a combination square, check to see if the blade angle is 45 ° to the table.

3.If the blade is not at 45 ° to the miter table, tilt the cutting arm to the right, loosen the Iocknut (8) on the bevel angle adjustment bolt (9) and use a 10 mm wrench to adjust the stop bolt (9) depth in or out to increase or decrease the bevel angle.

4.Tilt the cutting arm to the left to 45° bevel and recheck for align ment.

5.Repeat steps 1 through 4 until the blade is at 45 ° to the miter table.

6.Tighten bevel lock handle (7) and Iocknut (8) when alignment is achieved

Fig. N

10 i

7

i

9_----

J

12

8

 

 

11

33.9° Bevel Adjustment (Fig. N)

1.Push the bevel detent pin (10) in toward the front of the unit.

2.Unlock the bevel lock handle and tilt the cutting arm to the crown molding positive stop at 33.9 °

3.Using a combination square, check to see if the blade angle is 33.90 to the table.

4.If the blade is not at 33.90 to the miter table, loosen Iocknut (11 ) and use a 10 mm wrench to adjust the bolt (12) in or out until the blade is at 33.9 ° to the miter table.

5.Secure the Iocknut (11) into position after alignment is achieved.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents CRSFrSMSN Model NoBlade Ection PAG E SectionMotor Miter SAW Rotating TableCheck for Damaged PARTS. Check for Disconnect Tools from Power SourceUSE Proper Extension CORDS. Make sure Keep the Motor AIR Slots Clean and free of chips or dust Power Supply and Motor SpecificationsMotor Safety Protection Double InsulatedIL Warning Recommended AccessoriesAccessories Combination Square Must be TrueIA Warning Unpacking Your Miter SAWPage Woodworking Terms Unlocking the Slide Carriage FIG. B Estimated Assembly Time 5 10 minutesINSTALLiNG the Dust BAG FIG. D RaisingIAWARNmNG INSTALLiNG the HOLD-DOWN ClampWARNINe Mounting the Miter SAW FIG. G, G=IRemoving and Installing the Blade MountinginstructionsAvoid Direct EYE Contact Laser Guide FIG. KFrom turning the machine on Bevel Stop Adjustment Bevel Adjustment Fig. NMiter Scale Indicator Adjustment FIG. O Miter Angle Adjustment FIG. OSetting Cutting Depth FIG. Q Adjusting Fence Squareness FIG. PRecommended Accessories Before Using the Miter SAWSafety and Operations Sections Keep Your Work Area CleanPlan Your Work Dress for SafetyWhen SAW is Running Do not OverreachBody and Hand Position FIG. R Before freeing jammed material 6 Release trigger switchIAWARNmNO To Turn SAW on FIG. SBefore Leaving the SAW WAR.mr,JGISliding Carriage System FIG Miter CUT FIG. UCompound CUT FIG IAWANiGIBevel Stop for Crown Molding FIG. W Slide Cutting Wide Boards UP to 12 in. WideCutting Bowed Material FIG. Z Auxiliary Wood Fence FIG. CCCutting Crown Molding FIG. EE, FF Bevel/Miter SettingsCuttingbasemolding FIG. DD Inside corner-Left sideCrown Molding Chart IAwARJG MaintenanceAWARmG Problem Cause Suggested Corrective Action Problem Problem Cause Suggested Corrective ActionParts List for SAW Schematic 10INSUDINGCOMPOUNDMtTESAW.MODEL.O137.212370Schematic for SAW Parts List and Schematic for Motor SAW ModelPage Your Home

137.21237 specifications

The Craftsman 137.21237 table saw is a versatile and robust woodworking tool that caters to both amateur and professional woodworkers. Renowned for its reliability and precision, this table saw has made a mark in the DIY community and among seasoned craftspeople alike.

One of the standout features of the Craftsman 137.21237 is its powerful motor. With a 15-amp motor, it provides ample power to tackle a variety of cutting tasks. This motor facilitates smooth cuts through hardwoods and thick materials, ensuring that users experience consistent performance without lag. The saw comes equipped with a 10-inch blade that spins at impressive RPMs, allowing for clean, efficient cuts across different types of wood and plywood.

Another key characteristic of this table saw is its durable construction. The table surface is made of cast iron, providing a stable base that minimizes vibrations during operation. This stability is crucial for achieving accuracy in cuts, especially for intricate projects that require precise measurements. The table itself measures a generous size, allowing for larger workpieces to be cut with ease.

The Craftsman 137.21237 also boasts an advanced rip fence system. The fence is designed for quick adjustments, enabling users to make straight, consistent cuts at various widths. The easy locking mechanism ensures that your settings remain in place while cutting, enhancing safety and accuracy.

Safety is a paramount concern with the Craftsman 137.21237. It features an integrated blade guard, which provides protection against accidental contact with the blade. Additionally, the saw includes riving knife technology, which helps prevent kickback by keeping the wood aligned during cuts. This safety technology is crucial for woodworkers looking to minimize risk while operating powerful equipment.

Portability is another important aspect of the Craftsman 137.21237. Despite its sturdy build, the saw is designed with user convenience in mind. It includes onboard storage for accessories and additional parts, as well as a foldable stand, making it easy to transport and store when not in use.

In summary, the Craftsman 137.21237 table saw combines power, durability, and precision. With its strong 15-amp motor, robust cast iron construction, advanced safety features, and user-friendly design, it stands out as a reliable choice for anyone engaged in woodworking projects. Whether you're building furniture, crafting cabinetry, or undertaking home improvement tasks, this table saw provides the functionality and performance that can enhance your woodworking experience.
Top Page Image Contents