Craftsman 137.248830 RIP Fence Indicator Adjustment FIG. Q, Stop, Blade Tilting Pointer

Page 14

RIP FENCE INDICATOR ADJUSTMENT (FIG. Q)

1.The rip fence indicator (6) points to the measurement scale. The scale shows the distance from the side of the fence to nearest side of the blade.

2.Measure the actual distance with a rule. If there is a difference between the measurement and the indicator, adjust the indicator (6).

3.Loosen the screw (7) and slide the indicator to the correct measurement on the scale. Tighten the screw and remeasure with the rule.

IA WARNING

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

ADJUSTING THE 90 ° AND 45" POSITIVE STOPS (FIG.Q-I, Q-2,Q-3)

Your saw has positive stops that will quickly position the saw blade at 90° to the table. Make adjustments only if necessary.

90 ° Stop

1.Disconnect the saw from the power source.

2.Turn the blade elevation handwheel and raise the blade to the maximum elevation.

3.Loosen the blade bevel lock handle (2) and

move the blade to the maximum vertical position. Tighten the lock handle (2).

4.Place a combination square on the table and against the blade (t)to determine if the blade is 90° to the table. (Fig. Q-2)

5.If the blade is not 90° to the table, loosen the two set screws (4), located underneath the table saw, (Fig. Q-3) with the hex key, and back off the collar..

6.Loosen the bevel lock knob. Turn the blade

tilting handwheel to move the blade until it is 90° to the table.

7.Adjust the collar (5) so it contacts the bracket (3) when the blade is 90° to the table. Tighten the two set screws (4).

Fig. Q-1

Fig. Q-2

90°45°

3

45 ° Stop

1.With the blade in the upright 90° position, loosen the bevel lock knob and move the blade to the

45° position as far as it will go.

2.Place the combination square on the table as shown in (Fig.Q-2) to check if the blade is 45° to the table.

3.If the blade is not 45° to the table, loosen the two set screws (4) (Fig. Q-3) with the hex key. Back- off the collar (5) then align the blade 45° to the table, adjust the collar (5) so it contacts the bracket (3).

4.Retighten the two set screws (4).

BLADE TILTING POINTER

1.When the blade is positioned at 90°, adjust the blade tilting pointer to read 0° on the scale.

2.Loosen the holding screw, position pointer over 0° and tighten the screw.

NOTE: Make a trial cut on scrap wood before making critical cuts. Measure for exactness.

Fig. Q-3

345

Image 14
Contents Operators Manual SAW Full ONE Year WarrantyMotor 5000Sawing Operations IA Warningi AmputationsAWG type / 120 Volt only Any extension cord must be Grounded for safe operationMinimum Gauge for Extension Cords Event of a Malfunction orIk Warningi Unpacking Your Table SAW PqrstvwExtension wing Page Blade Tilting Handwheel FIG. G, F SAW Mounted to Work Surface FIG. CBlade Raising Handwheel FIG. E, F Installing and Changing the Blade FIG. H, I, J Iz,WARNINGlBlade Guard Assembly FIG. K, L, M Installing Table Side Extensions FIG. NAdjusting Rear Table Extension Installing the Table Side EXTENSIONS- contd FIG. OInstalling Rear Table Extension FIG. P RIP Fence Adjustment FIG. QStop RIP Fence Indicator Adjustment FIG. QAdjusting the 90 and 45 Positive Stops FIG.Q-I, Q-2,Q-3 Blade Tilting PointerIwarning Blade Parallel to the Miter Gauge Groove FIG. R,STilting the Blade FIG. T ON/OFF Switch FIG. URaise the Blade FIG. T Overload Protection FIG. UCutting Operations Ripping FIG. WCrosscutting FIG. Y Bevel RippingRipping Small Pieces Bevel Crosscutting FIG. ZAuxiliary Fence FIG. CC-1 Using Wood Facing on the RIP Fence FIG. CCMitering FIG. BB Making the baseFig. EE LubricationMakingany adjustments Symptom Possible Causes Corrective ActionAlways order by Model Number and I.D. number Schematic a QtyCO CO Schematic OT04 Table SAW Page Part list for Motor 113 Cut off here to Push 1/2 wood MY-HOME

137.248830 specifications

The Craftsman 137.248830 is a versatile and powerful table saw that has garnered attention among DIY enthusiasts and professional woodworkers alike. With its robust construction and user-friendly features, it stands out as a reliable choice for tackling a variety of woodworking projects.

One of the main attributes of the Craftsman 137.248830 is its precision. It comes equipped with a 10-inch blade that offers excellent cutting capabilities for a wide range of materials, including hardwood, plywood, and softwood. The saw utilizes a direct drive motor that delivers a powerful 15-amp output, ensuring consistent and efficient cutting performance.

Safety is a priority in this model, featuring an integrated blade guard system that protects users during operation. The saw also includes a riving knife, which helps prevent kickback by keeping the material aligned with the blade, enhancing overall safety while making cuts. Additionally, the push stick and safety switch are designed to further minimize risk, making it suitable for users of various skill levels.

Another prominent feature is its adjustable dual-sided fence system, which provides accurate and secure measurements for precise cuts. The fence can be easily adjusted, making it ideal for rip cuts as well as crosscuts. Furthermore, the measuring scale is clear and easy to read, allowing woodworkers to set up their projects quickly.

Portability is another characteristic that stands out. The Craftsman 137.248830 is designed with a foldable stand, making it easy to transport to job sites or store when not in use. Despite its sturdy construction, the saw remains lightweight enough for easy maneuverability.

Moreover, the onboard storage provides convenient access to all necessary tools, such as blades and wrenches, keeping everything organized . The dust port is also a noteworthy feature; it helps maintain a clean workspace by connecting to a dust extractor, which is essential for creating a safe working environment.

In summary, the Craftsman 137.248830 table saw combines power, precision, and safety features, making it a fantastic addition to any woodworking shop. Its reliable performance, user-friendly design, and portable nature cater to both amateur and professional woodworkers seeking quality in their tools.