Craftsman 137.248830 operating instructions Any extension cord must be Grounded for safe operation

Page 5

POWER SUPPLY REQUIREMENTS

IA WARNING]

To avoidelectricalhazards,firehazardsordamage tothe tablesaw, use propercircuitprotectionAlways. use a

separate electrical circuit for your tools. This power tool is wired at the factory for 120V operation. Connect it to a 120V, 15 Amp circuit and use a 15 Amp time delay fuse or circuit breaker. To avoid shock or fire, replace the cord immediately if it is worn, cut or damaged in any way.

EXTENSION CORD REQUIREMENTS

In WARNING]

Any extension cord must be GROUNDED for safe operation.

MINIMUM GAUGE FOR EXTENSION CORDS

(AWG type / 120 Volt only)

Ampere

Rating

Total length in feet

 

Not

 

 

 

 

More Than

More Than

25'

50'

100'

150'

0

6

18

16

16

14

6

10

18

16

14

12

10

12

16

16

14

12

GUIDELINES FOR EXTENSION CORDS

Any extension cord used for power tools MUST be grounded (3-wire with two flat prongs and one round ground prong).

Make sure the extension cord is in good condition. When using an extension cord, make sure you use one heavy enough to carry the current the tool will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table above shows the correct size to use according to extension cord length and nameplate ampere rating. If in doubt, use the next heavier gauge cord. The smaller the gauge number the heavier the cord.

NOTE: The 12 to 16 Amp rating is correct for this tool. It is highlighted in the table above.

Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

Before connecting the saw to the extension cord, make sure the saw switch is turned OFF.

GROUNDING INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR

BREAKDOWN, grounding provides a path of least resistance for electric current and reduces the risk of

electric shock. This saw is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.

IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock. The

conductor (wire) with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal.

CHECK with a qualified electrician or service personnel if you do not completely understand the grounding instructions, or if you are not sure the saw is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole grounding receptacles that accept the saw'splug. Repair or replace damaged or worn cords immediately.

3-Prong Plug

Grou_ng Lug

_._--_._

 

_'/

_--

Make Sure This

__

 

It isC_nec_edtoa

%J-X

 

Known G rc_nd

 

iF"

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operators Manual Motor Full ONE Year WarrantySAW 5000Sawing Operations Amputations IA WarningiMinimum Gauge for Extension Cords Any extension cord must be Grounded for safe operationAWG type / 120 Volt only Event of a Malfunction orIk Warningi Pqrstvw Unpacking Your Table SAWExtension wing Page Blade Tilting Handwheel FIG. G, F SAW Mounted to Work Surface FIG. CBlade Raising Handwheel FIG. E, F Iz,WARNINGl Installing and Changing the Blade FIG. H, I, JInstalling Table Side Extensions FIG. N Blade Guard Assembly FIG. K, L, MInstalling Rear Table Extension FIG. P Installing the Table Side EXTENSIONS- contd FIG. OAdjusting Rear Table Extension RIP Fence Adjustment FIG. QAdjusting the 90 and 45 Positive Stops FIG.Q-I, Q-2,Q-3 RIP Fence Indicator Adjustment FIG. QStop Blade Tilting PointerBlade Parallel to the Miter Gauge Groove FIG. R,S IwarningRaise the Blade FIG. T ON/OFF Switch FIG. UTilting the Blade FIG. T Overload Protection FIG. URipping FIG. W Cutting OperationsRipping Small Pieces Bevel RippingCrosscutting FIG. Y Bevel Crosscutting FIG. ZMitering FIG. BB Using Wood Facing on the RIP Fence FIG. CCAuxiliary Fence FIG. CC-1 Making the baseLubrication Fig. EESymptom Possible Causes Corrective Action Makingany adjustmentsQty Always order by Model Number and I.D. number Schematic aCO CO Schematic OT04 Table SAW Page Part list for Motor 113 Cut off here to Push 1/2 wood MY-HOME

137.248830 specifications

The Craftsman 137.248830 is a versatile and powerful table saw that has garnered attention among DIY enthusiasts and professional woodworkers alike. With its robust construction and user-friendly features, it stands out as a reliable choice for tackling a variety of woodworking projects.

One of the main attributes of the Craftsman 137.248830 is its precision. It comes equipped with a 10-inch blade that offers excellent cutting capabilities for a wide range of materials, including hardwood, plywood, and softwood. The saw utilizes a direct drive motor that delivers a powerful 15-amp output, ensuring consistent and efficient cutting performance.

Safety is a priority in this model, featuring an integrated blade guard system that protects users during operation. The saw also includes a riving knife, which helps prevent kickback by keeping the material aligned with the blade, enhancing overall safety while making cuts. Additionally, the push stick and safety switch are designed to further minimize risk, making it suitable for users of various skill levels.

Another prominent feature is its adjustable dual-sided fence system, which provides accurate and secure measurements for precise cuts. The fence can be easily adjusted, making it ideal for rip cuts as well as crosscuts. Furthermore, the measuring scale is clear and easy to read, allowing woodworkers to set up their projects quickly.

Portability is another characteristic that stands out. The Craftsman 137.248830 is designed with a foldable stand, making it easy to transport to job sites or store when not in use. Despite its sturdy construction, the saw remains lightweight enough for easy maneuverability.

Moreover, the onboard storage provides convenient access to all necessary tools, such as blades and wrenches, keeping everything organized . The dust port is also a noteworthy feature; it helps maintain a clean workspace by connecting to a dust extractor, which is essential for creating a safe working environment.

In summary, the Craftsman 137.248830 table saw combines power, precision, and safety features, making it a fantastic addition to any woodworking shop. Its reliable performance, user-friendly design, and portable nature cater to both amateur and professional woodworkers seeking quality in their tools.
Top Page Image Contents