Craftsman 137.248830 operating instructions Cutting Operations, Ripping FIG. W

Page 17

CUTTING OPERATIONS

Fig. W

There are two basic types of cuts: ripping and

 

crosscutting. Ripping is cutting along the length and

 

the grain of the workpiece. Crosscutting is cutting

 

either across the width or across the grain of the

 

workpiece. Neither ripping nor crosscutting may be

 

done safely freehand. Ripping requires the use of the

 

rip fence, and crosscutting requires the miter gauge.

 

LA WARNINGJ

Before using the saw each and every time, check the following:

1.Blade is tight on the arbor.

2.Bevel angle lock knob is tight.

3.If ripping, fence knob is tight and fence is parallel to the miter gauge grooves.

4.Blade guard is in place and working properly.

5.Safety glasses are being worn.

The failure to adhere to these common safety rules, and those printed in the front of this manual, can greatly increase the likelihood of injury.

RIPPING (FIG. W, X)

WARNING

To prevent serious injury:

•Never use the miter gauge when ripping.

•Never use more than one rip fence during a single cut.

•Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that

even a careless fraction of a second is enough to cause a severe injury.

•Keep both hands away from the blade and path of the blade.

•The workpiece must have a straight edge against

the fence and must not be warped, twisted, or bowed.

1.Remove the miter gauge. Secure the rip fence to the table.

2.Raise the blade so it is about 1/8" higher than the top of the workpiece.

3.Place the workpiece flat on the table and against the fence. Keep the workpiece away from the blade.

4.Turn the saw ON and wait for the blade to come up to speed.

5.Slowly feed the workpiece into the blade by pushing forward only on the workpiece section (1) that will pass between the blade and the fence. (Fig. W)

NOTE: Always use a push stick. When width or rip narrower than 2" the push stick cannot be used because the guard will interfere... Use the auxiliary fence as shown are page 19.

6.Keep your thumbs off the table top. When both of your thumbs touch the front edge of the table (2), finish the cut with a push stick. Make a push stick using the pattern on page 30.

7.The push stick (3) should always be used. (Fig. X)

8.Continue pushing the workpiece with the push stick

(3)until it passes the blade guard and clears the rear of the table.

9.Never pull the piece back when the blade is turning. Turn the switch OFF. When the blade completely stops, then remove the workpiece.

Fig. X

[,_ WARNING]

AVOID KICKBACK by pushingforwardon thesection oftheworkpiecethatpasses betweenthebladeand thefence.

]?

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operators Manual Motor Full ONE Year WarrantySAW 5000Sawing Operations Amputations IA WarningiMinimum Gauge for Extension Cords Any extension cord must be Grounded for safe operationAWG type / 120 Volt only Event of a Malfunction orIk Warningi Pqrstvw Unpacking Your Table SAWExtension wing Page Blade Tilting Handwheel FIG. G, F SAW Mounted to Work Surface FIG. CBlade Raising Handwheel FIG. E, F Iz,WARNINGl Installing and Changing the Blade FIG. H, I, JInstalling Table Side Extensions FIG. N Blade Guard Assembly FIG. K, L, MInstalling Rear Table Extension FIG. P Installing the Table Side EXTENSIONS- contd FIG. OAdjusting Rear Table Extension RIP Fence Adjustment FIG. QAdjusting the 90 and 45 Positive Stops FIG.Q-I, Q-2,Q-3 RIP Fence Indicator Adjustment FIG. QStop Blade Tilting PointerBlade Parallel to the Miter Gauge Groove FIG. R,S IwarningRaise the Blade FIG. T ON/OFF Switch FIG. UTilting the Blade FIG. T Overload Protection FIG. URipping FIG. W Cutting OperationsRipping Small Pieces Bevel RippingCrosscutting FIG. Y Bevel Crosscutting FIG. ZMitering FIG. BB Using Wood Facing on the RIP Fence FIG. CCAuxiliary Fence FIG. CC-1 Making the baseLubrication Fig. EESymptom Possible Causes Corrective Action Makingany adjustmentsQty Always order by Model Number and I.D. number Schematic aCO CO Schematic OT04 Table SAW Page Part list for Motor 113 Cut off here to Push 1/2 wood MY-HOME

137.248830 specifications

The Craftsman 137.248830 is a versatile and powerful table saw that has garnered attention among DIY enthusiasts and professional woodworkers alike. With its robust construction and user-friendly features, it stands out as a reliable choice for tackling a variety of woodworking projects.

One of the main attributes of the Craftsman 137.248830 is its precision. It comes equipped with a 10-inch blade that offers excellent cutting capabilities for a wide range of materials, including hardwood, plywood, and softwood. The saw utilizes a direct drive motor that delivers a powerful 15-amp output, ensuring consistent and efficient cutting performance.

Safety is a priority in this model, featuring an integrated blade guard system that protects users during operation. The saw also includes a riving knife, which helps prevent kickback by keeping the material aligned with the blade, enhancing overall safety while making cuts. Additionally, the push stick and safety switch are designed to further minimize risk, making it suitable for users of various skill levels.

Another prominent feature is its adjustable dual-sided fence system, which provides accurate and secure measurements for precise cuts. The fence can be easily adjusted, making it ideal for rip cuts as well as crosscuts. Furthermore, the measuring scale is clear and easy to read, allowing woodworkers to set up their projects quickly.

Portability is another characteristic that stands out. The Craftsman 137.248830 is designed with a foldable stand, making it easy to transport to job sites or store when not in use. Despite its sturdy construction, the saw remains lightweight enough for easy maneuverability.

Moreover, the onboard storage provides convenient access to all necessary tools, such as blades and wrenches, keeping everything organized . The dust port is also a noteworthy feature; it helps maintain a clean workspace by connecting to a dust extractor, which is essential for creating a safe working environment.

In summary, the Craftsman 137.248830 table saw combines power, precision, and safety features, making it a fantastic addition to any woodworking shop. Its reliable performance, user-friendly design, and portable nature cater to both amateur and professional woodworkers seeking quality in their tools.
Top Page Image Contents