Craftsman 137.248830 Iwarning, Blade Parallel to the Miter Gauge Groove FIG. R,S

Page 15

BLADE PARALLEL TO THE MITER GAUGE GROOVE (FIG. R,S)

I_WARNING

This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

IAWARNING

To preventpersonalinjury:

•Always disconnectplugfromthepower source when making any adjustments.

•Thisadjustmentmust be correctorkickback could result in a serious injury and accurate cuts can not be made.

1.Remove the yellow switch key and unplug the saw.

2.Move the blade guard out of the way.

3.Raise the blade to the highest position and set at the 0° angle (90° straight up).

4.Select and mark, with a felt tip marker, a blade tooth having a "right set". Angle and positioning this tooth 1/2" above the table at the front of the

saw.

5.Place the combination square base (1) into the right side miter gauge groove (2). (Fig. R)

6.Adjust the rule so it touches the front marked tooth and lock ruler so it holds its position in the square assembly.

7.Rotate the blade bringing the marked tooth to the rear and about 1/2 inch above the blade.

8.Carefully slide the combination square to the rear until the ruler touches the marked tooth.

9.If the ruler touches the marked tooth at the front and rear position, no adjustment is needed at this time. If not, perform the adjustment procedure described in next section.

Fig. R

Additional blade adjustments (Fig. S) NOTE: The adjusting nuts are 8mm.

The adjusting mechanism is located above the blade height adjusting hand wheel under the tabletop. If the front and rear measurements are not the same, adjust the alignment by the mechanism as follows:

If the blade is partial to right side:

1.Loosen the two nuts (1) and the right side screw, then adjust the left side screw.

2.Tighten the nuts (1) and the right screw and remeasure, as described in steps 4 to 9 in the prior section.

If the blade is partial to left side:

3.Loosen the two nuts (t) and the left side screw, then adjust the right screw to its position.

4.Tighten the nuts (t) and the left screw and remeasure, as described in steps 4 to 9 in the prior section.

5.Recheck blade clearance making sure that the blade does not hit the table insert or other parts when at the 90° and 45° settings.

Fig. S

f

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operators Manual 5000 Full ONE Year WarrantyMotor SAWSawing Operations Amputations IA WarningiEvent of a Malfunction or Any extension cord must be Grounded for safe operationMinimum Gauge for Extension Cords AWG type / 120 Volt onlyIk Warningi Pqrstvw Unpacking Your Table SAWExtension wing Page SAW Mounted to Work Surface FIG. C Blade Raising Handwheel FIG. E, FBlade Tilting Handwheel FIG. G, F Iz,WARNINGl Installing and Changing the Blade FIG. H, I, JInstalling Table Side Extensions FIG. N Blade Guard Assembly FIG. K, L, MRIP Fence Adjustment FIG. Q Installing the Table Side EXTENSIONS- contd FIG. OInstalling Rear Table Extension FIG. P Adjusting Rear Table ExtensionBlade Tilting Pointer RIP Fence Indicator Adjustment FIG. QAdjusting the 90 and 45 Positive Stops FIG.Q-I, Q-2,Q-3 StopBlade Parallel to the Miter Gauge Groove FIG. R,S IwarningOverload Protection FIG. U ON/OFF Switch FIG. URaise the Blade FIG. T Tilting the Blade FIG. TRipping FIG. W Cutting OperationsBevel Crosscutting FIG. Z Bevel RippingRipping Small Pieces Crosscutting FIG. YMaking the base Using Wood Facing on the RIP Fence FIG. CCMitering FIG. BB Auxiliary Fence FIG. CC-1Lubrication Fig. EESymptom Possible Causes Corrective Action Makingany adjustmentsQty Always order by Model Number and I.D. number Schematic aCO CO Schematic OT04 Table SAW Page Part list for Motor 113 Cut off here to Push 1/2 wood MY-HOME

137.248830 specifications

The Craftsman 137.248830 is a versatile and powerful table saw that has garnered attention among DIY enthusiasts and professional woodworkers alike. With its robust construction and user-friendly features, it stands out as a reliable choice for tackling a variety of woodworking projects.

One of the main attributes of the Craftsman 137.248830 is its precision. It comes equipped with a 10-inch blade that offers excellent cutting capabilities for a wide range of materials, including hardwood, plywood, and softwood. The saw utilizes a direct drive motor that delivers a powerful 15-amp output, ensuring consistent and efficient cutting performance.

Safety is a priority in this model, featuring an integrated blade guard system that protects users during operation. The saw also includes a riving knife, which helps prevent kickback by keeping the material aligned with the blade, enhancing overall safety while making cuts. Additionally, the push stick and safety switch are designed to further minimize risk, making it suitable for users of various skill levels.

Another prominent feature is its adjustable dual-sided fence system, which provides accurate and secure measurements for precise cuts. The fence can be easily adjusted, making it ideal for rip cuts as well as crosscuts. Furthermore, the measuring scale is clear and easy to read, allowing woodworkers to set up their projects quickly.

Portability is another characteristic that stands out. The Craftsman 137.248830 is designed with a foldable stand, making it easy to transport to job sites or store when not in use. Despite its sturdy construction, the saw remains lightweight enough for easy maneuverability.

Moreover, the onboard storage provides convenient access to all necessary tools, such as blades and wrenches, keeping everything organized . The dust port is also a noteworthy feature; it helps maintain a clean workspace by connecting to a dust extractor, which is essential for creating a safe working environment.

In summary, the Craftsman 137.248830 table saw combines power, precision, and safety features, making it a fantastic addition to any woodworking shop. Its reliable performance, user-friendly design, and portable nature cater to both amateur and professional woodworkers seeking quality in their tools.
Top Page Image Contents