Craftsman 137.248830 Mitering FIG. BB, Using Wood Facing on the RIP Fence FIG. CC

Page 19

MITERING (FIG. BB)

This sawing operation is the same as crosscutting

except the miter gauge is locked at an angle other than 90°

1_Hold the workpiece (2) firmly against the miter gauge (3).

2.Feed the workpiece slowly into the blade (1) to prevent the workpiece from moving.

Fig. BB

2

Fig. CC-1

30"

3/8'Thick plywood base

27"i

Attach auxiliary fence to rip fence with two "C" clamps. (Fig. CC-2)

USING WOOD FACING ON THE RIP FENCE (FIG. CC)

When performing some special cutting operations, add a wood facing (1) to either side of the rip fence (2).

1.Use a smooth straight 3/4" thick wood board (1) that is as long as the rip fence.

2.Attach the wood facing to the fence with wood screw

(3) through the hole in the fence. A wood fence should be used when ripping material such as thin paneling to prevent the material from catching between the bottom of the fence and the table.

Fig. CC

AUXILIARY FENCE (FIG. CC-1)

Making the base:

•Start with a piece of 3/8" plywood at least 5-1/2" wide or wider and 30" long or longer.

•Cut the piece to shape and size shown:

Making the side:

• Start with a piece of 3/4" plywood at least 2-3/8"

wide or wider and 27" long or longer/

Fig. CC-2

DADO CUTS (FIG. DD)

1.The dado table insert is included with this saw.

Remove saw blade, blade guard, then install the dado, and dado table insert.

2.Instruction for operating the dado is packed with the separately purchased dado set.

3.The arbor (1) on this saw restricts the maximum width of the cut to 1/2".

4.It is not necessary to install the outside flange (2) before screwing on the arbor nut (3). Make sure that the arbor nut (3) is tight, and that at least one thread of the arbor sticks out past the nut.

5.Use only the 6" dado set and keep the width t/2" or less. It will be necessary to remove the blade guard and splitter when using a dado blade. Always use caution when operating a dado blade.

6.Use only the correct number of round outside blades and inside chippers as shown in the dado set's

instruction manual. Blades/chippers must not exceed 1/2".

7.Check saw to ensure that the dado will not strike the housing, insert, or motor when in operation.

IIILWARNING l

For your own safety, always replace the blade, blade guard assembly, and blade insert when you are finished with the dado operation.

• Cut the piece to shape and size shown:

Putting it together:

•Put the pieces together, as shown:

[A'iWARNING I

Make sure the screw heads do not stick out from the

bottom of the base, they must be flush or recessed. The bottom must be flat and smooth enough to rest on the saw table without rocking.

Fig. DD

z_z

j2

J

\

'_3

]9

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operators Manual 5000 Full ONE Year WarrantyMotor SAWSawing Operations Amputations IA WarningiEvent of a Malfunction or Any extension cord must be Grounded for safe operationMinimum Gauge for Extension Cords AWG type / 120 Volt onlyIk Warningi Pqrstvw Unpacking Your Table SAWExtension wing Page Blade Raising Handwheel FIG. E, F SAW Mounted to Work Surface FIG. CBlade Tilting Handwheel FIG. G, F Iz,WARNINGl Installing and Changing the Blade FIG. H, I, JInstalling Table Side Extensions FIG. N Blade Guard Assembly FIG. K, L, MRIP Fence Adjustment FIG. Q Installing the Table Side EXTENSIONS- contd FIG. OInstalling Rear Table Extension FIG. P Adjusting Rear Table ExtensionBlade Tilting Pointer RIP Fence Indicator Adjustment FIG. QAdjusting the 90 and 45 Positive Stops FIG.Q-I, Q-2,Q-3 StopBlade Parallel to the Miter Gauge Groove FIG. R,S IwarningOverload Protection FIG. U ON/OFF Switch FIG. URaise the Blade FIG. T Tilting the Blade FIG. TRipping FIG. W Cutting OperationsBevel Crosscutting FIG. Z Bevel RippingRipping Small Pieces Crosscutting FIG. YMaking the base Using Wood Facing on the RIP Fence FIG. CCMitering FIG. BB Auxiliary Fence FIG. CC-1Lubrication Fig. EESymptom Possible Causes Corrective Action Makingany adjustmentsQty Always order by Model Number and I.D. number Schematic aCO CO Schematic OT04 Table SAW Page Part list for Motor 113 Cut off here to Push 1/2 wood MY-HOME

137.248830 specifications

The Craftsman 137.248830 is a versatile and powerful table saw that has garnered attention among DIY enthusiasts and professional woodworkers alike. With its robust construction and user-friendly features, it stands out as a reliable choice for tackling a variety of woodworking projects.

One of the main attributes of the Craftsman 137.248830 is its precision. It comes equipped with a 10-inch blade that offers excellent cutting capabilities for a wide range of materials, including hardwood, plywood, and softwood. The saw utilizes a direct drive motor that delivers a powerful 15-amp output, ensuring consistent and efficient cutting performance.

Safety is a priority in this model, featuring an integrated blade guard system that protects users during operation. The saw also includes a riving knife, which helps prevent kickback by keeping the material aligned with the blade, enhancing overall safety while making cuts. Additionally, the push stick and safety switch are designed to further minimize risk, making it suitable for users of various skill levels.

Another prominent feature is its adjustable dual-sided fence system, which provides accurate and secure measurements for precise cuts. The fence can be easily adjusted, making it ideal for rip cuts as well as crosscuts. Furthermore, the measuring scale is clear and easy to read, allowing woodworkers to set up their projects quickly.

Portability is another characteristic that stands out. The Craftsman 137.248830 is designed with a foldable stand, making it easy to transport to job sites or store when not in use. Despite its sturdy construction, the saw remains lightweight enough for easy maneuverability.

Moreover, the onboard storage provides convenient access to all necessary tools, such as blades and wrenches, keeping everything organized . The dust port is also a noteworthy feature; it helps maintain a clean workspace by connecting to a dust extractor, which is essential for creating a safe working environment.

In summary, the Craftsman 137.248830 table saw combines power, precision, and safety features, making it a fantastic addition to any woodworking shop. Its reliable performance, user-friendly design, and portable nature cater to both amateur and professional woodworkers seeking quality in their tools.
Top Page Image Contents