Graco ti15036b Equipment Misuse Hazard, Electric Shock Hazard, Pressurized Aluminum Parts Hazard

Page 6

Warnings

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Always wear appropriate gloves, eye protection, and a respirator or mask when painting.

Do not operate or spray near children. Keep children away from equipment at all times.

Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.

Stay alert and watch what you are doing.

Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn off the unit and follow the Pressure Relief Procedure for turning off the unit.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

Do not kink or over-bend the hose.

Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.

Do not use the hose as a strength member to pull or lift the equipment.

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.

Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.

Connect only to grounded power source.

All electrical wiring must be done by a qualified electrician and comply with all local codes and regula- tions.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage.

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.

Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for compatibility.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

Keep clear of moving parts.

Do not operate equipment with protective guards or covers removed.

Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, fol- low the Pressure Relief Procedure and disconnect all power sources.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. This equipment includes but is not limited to:

Protective eyewear, and hearing protection.

Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

6

3A0157B

Image 6
Contents Electric Airless Sprayers MarkModels Ultra MAX lIlTable of Contents Grounding Extension CordsFire and Explosion Hazard Skin Injection HazardPressurized Aluminum Parts Hazard Equipment Misuse HazardElectric Shock Hazard Moving Parts HazardComponent Identification Pressure Relief Procedure Extension Cord Power RequirementsGrounding PailsWhat to Check What to do Type of Problem TroubleshootingPerform Pressure Relief Procedure Mechanical/Fluid FlowFollow Pressure Relief Procedure on What to Check What to do Type of Problem Type of Problem What to Check HOW to Check ElectricalCheck to see if transducer and control board Step Check Motor Thermal Switch Unplug thermal Is not correct, replace motor Sprayer Will Not Shut Off YESSprayer Will Not Run Step Removal Installation VAC and 110 VAC Motor Control Board33 D 115 VAC Filter Board RemovalPressure Adjust Potentiometer Pressure Control Transducer Install control box 61 and control panel 68 with four screws 3A0157B Drive and Bearing Housing Replacement DisassemblyAssembly Drive and Bearing Housing Replacement Install Motor Shroud Motor ReplacementInstallation RemovalMotor Replacement Displacement Pump Replacement for 695/795/Mark Perform Relieve Pressure ProcedureTi7169a Displacement Pump Replacement 1095/1595/Mark Perform Pressure Relief Procedure,Place u-bolt on pump door protrusion Attach drain hose to sprayer Hose Reel Grease shaft Reed Switch Replacement RemovalInstallationWiring Diagram 120V ModelsON/OFF 120V Models with 15/20 Amp Switch 240V Models Thermal Switch Motor Leads SensorDip Switch AutoClean Watchdog Digital Display Potentiometer Pressure Transducer3A0157B Graco Standard Warranty Graco Information