Graco 334466A important safety instructions Grounding, Extension Cords

Page 4

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

GROUNDING

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

•Improper installation of the grounding plug is able to result in a risk of electric shock.

•When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade terminal.

•The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

•Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or when in doubt as to whether the product is properly grounded.

•Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electrician.

•This product is for use on a nominal 110V, 120V, or 230V circuit and has a grounding plug similar to the plugs illustrated below.

120V US

230V

230V ANZ

ti24583a

•Only connect the product to an outlet having the same configuration as the plug.

•Do not use an adapter with this product.

Extension Cords:

•Use only a 3-wire extension cord that has a grounding plug and a grounding receptacle that accepts the plug on the product.

•Make sure your extension cord is not damaged. If an extension cord is necessary use 12 AWG (2.5mm2) minimum to carry the current that the product draws.

•An undersized cord results in a drop in line voltage and loss of power and overheating.

4

334466A

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Related Manuals Contractor/FTxSG3 334599Contents Stand Lo-Boy Hi-BoyModel Grounding Extension CordsFire and Explosion Hazard Equipment Misuse Hazard Personal Protective Equipment Component Identification Stand ModelsLo-Boy Models Hi-Boy Models Hi-Boy Models Power Requirements GroundingExtension Cords PailsPressure Relief Procedure Trigger Lock Setup 334466ATi24638a Make certain ON/OFF switch is OFF Turn prime valve horizontal. Disengage trigger lock Perform Pressure Relief Procedure, Startup20 s Ti24652a Spray Tip Installation Perform Pressure Relief Procedure,Operation SprayClear Tip Clog Digital Display Pressure Display Perform Pressure Relief Procedure,Stored Data Display Ti2824a Cleanup Raise fluid intake above flushing fluid Ti24719a Maintenance Activity IntervalMechanical/Fluid Flow TroubleshootingRefer to this column Properly installed to allow full Clockwise position. If problemHolders Dust with a small cleaning brush Piston packings are worn orPossible during priming Spray tip is partially cloggedFluid supply is low or empty Pump manual. Check fluid supplyProblem What to Check How to check ElectricalInstall new transducer. Connect Are clean and secureSprayer does not run at all Check transducer or transducer ConnectionsContacts are clean and secure Volt battery to the motorSize. Locate the two wires Should spin when battery isOhms Board Motor thermal device When cool, correct causeDisplay shows E=06 Basic electrical problems Replace loose terminals crimp toMotor. Check both brushes Rest squarely on top of brush Motor brushes may be bindingSprayer Will Not Run Sprayer Will Not RunStep Troubleshooting Procedure Sprayer Will Not Shut OffStand Sprayers Torque Ref. Part Description Stand Sprayers Parts ListQty Lo-Boy Sprayers Models 17C3156040 132 Lo-Boy Sprayers Parts List Models 17C315 Ref. Part DescriptionHi-Boy Sprayers Models 17C317, 17C362, 17C40840 44 117 Hi-Boy Sprayers Parts List Models 17C317, 17C362, 17C408 Ref. Part DescriptionAccessories and Labels Alert Control Box Control Box Parts List GrommetWiring Diagrams 120V, US/Japan110V, UK TP1 TP2Technical Specifications Ultra 395 PC / Ultra 395 PC ClassicMetric Materials of Construction Graco Standard Warranty For Graco Canada CustomersGraco Information International Offices Belgium, China, Japan, Korea
Top Page Image Contents