Graco 334466A important safety instructions Equipment Misuse Hazard

Page 6

Warnings

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Always wear appropriate gloves, eye protection, and a respirator or mask when painting.

•Do not operate or spray near children. Keep children away from equipment at all times.

•Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.

•Stay alert and watch what you are doing.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not kink or over-bend the hose.

•Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.

•Do not use the hose as a strength member to pull or lift the equipment.

•Do not spray with a hose shorter than 25 feet.

•Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you are using it.

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.

•Turn off and disconnect power cord before servicing equipment.

•Connect only to grounded electrical outlets.

•Use only 3-wire extension cords.

•Ensure ground prongs are intact on power and extension cords.

•Do not expose to rain. Store indoors.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage.

•Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.

•Do not use chlorine bleach.

•Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for compatibility.

MOVING PARTS HAZARD

Moving parts can pinch, cut, or amputate fingers and other body parts.

•Keep clear of moving parts.

•Do not operate equipment with protective guards or covers removed.

•Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

•Read MSDSs to know the specific hazards of the fluids you are using.

•Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

6

334466A

Page 5 Page 7
Image 6
Page 5 Page 7
Contents SG3 Related ManualsContractor/FTx 334599Contents Hi-Boy Stand Lo-BoyModel Grounding Extension CordsFire and Explosion Hazard Equipment Misuse Hazard Personal Protective Equipment Component Identification Stand ModelsLo-Boy Models Hi-Boy Models Hi-Boy Models Extension Cords Power RequirementsGrounding PailsPressure Relief Procedure Trigger Lock Setup 334466ATi24638a Make certain ON/OFF switch is OFF Turn prime valve horizontal. Disengage trigger lock Perform Pressure Relief Procedure, Startup20 s Ti24652a Operation Spray Tip InstallationPerform Pressure Relief Procedure, SprayClear Tip Clog Pressure Display Perform Pressure Relief Procedure, Digital DisplayStored Data Display Ti2824a Cleanup Raise fluid intake above flushing fluid Ti24719a Maintenance Activity IntervalTroubleshooting Mechanical/Fluid FlowRefer to this column Holders Dust with a small cleaning brush Properly installed to allow fullClockwise position. If problem Piston packings are worn orFluid supply is low or empty Possible during primingSpray tip is partially clogged Pump manual. Check fluid supplyProblem What to Check How to check ElectricalSprayer does not run at all Check transducer or transducer Install new transducer. ConnectAre clean and secure ConnectionsSize. Locate the two wires Contacts are clean and secureVolt battery to the motor Should spin when battery isOhms Motor thermal device When cool, correct cause BoardDisplay shows E=06 Motor. Check both brushes Basic electrical problemsReplace loose terminals crimp to Rest squarely on top of brush Motor brushes may be bindingSprayer Will Not Run Sprayer Will Not RunStep Troubleshooting Procedure Sprayer Will Not Shut OffStand Sprayers Torque Stand Sprayers Parts List Ref. Part DescriptionQty Lo-Boy Sprayers Models 17C3156040 132 Lo-Boy Sprayers Parts List Models 17C315 Ref. Part DescriptionHi-Boy Sprayers Models 17C317, 17C362, 17C40840 44 117 Hi-Boy Sprayers Parts List Models 17C317, 17C362, 17C408 Ref. Part DescriptionAccessories and Labels Alert Control Box Control Box Parts List GrommetWiring Diagrams 120V, US/Japan110V, UK TP1 TP2Technical Specifications Ultra 395 PC / Ultra 395 PC ClassicMetric Materials of Construction Graco Standard Warranty For Graco Canada CustomersGraco Information International Offices Belgium, China, Japan, Korea
Top Page Image Contents