I.C.T.C. Holdings Corporation 1240 GUN Extension WANDS, TOUCH-UP CUP KIT and Other Accessories

Page 23

6.5GUN EXTENSION WANDS, TOUCH-UP CUP KIT AND OTHER ACCESSORIES

Gun Extension Wands

For ease of use when spraying in hard to reach areas, ceilings, floors, decks, etc., Gun Extension Wands can be installed on any HERO gun with a spring loaded air cap. Wands are available in 12”, 18”, and 24” lengths. Specify the required Needle size when ordering – additional Needles can also be ordered as necessary.

Touch-Up Kit

When the 1 Qt/L cup on the cup-fed gun is too large, a Touch-Up Cup Kit can be installed on any HERO gun. The touch-up cup is the size of a spice jar and completely replaces the standard Cup Top Assembly and paint cup. The Touch-Up Kit allows the user to spray small quantities of material with the same gun as usual, without wasting material in a large cup.

2 Qt/L Paint Cup

When the 1Qt/L cup on the cup-fed gun is too small, a remote 2 Qt/L cup can be installed on any HERO gun. The 2 Qt/L cup can be pressurized by the turbine or by a compressor – the possibility of pressurizing with the turbine is dependent on the coating being sprayed. Remote 2 Qt/L cups are supplied with a Gun Conversion Kit (to convert from Cup-Fed Gun to Pressure-Fed Gun), 4’ air hose (from 2 Qt/L cup to gun), 4 ½’ fluid line (from 2 Qt/L cup to gun), and a shoulder strap.

Gun Accessory Kit

HERO Gun Accessory Kits are a practical selection (4 different sizes) of Needles, Fluid Tips, and Air Caps to ensure the ability to spray virtually any sprayable coating. Kits also include a Gun Cleaning Brush and (8) Siphon Tube Paint Filters.

Having a selection of accessories available has proven to be the difference between satisfaction and frustration when using any spraying system. Gun Accessory Kits can be purchased at a reduced price at time of purchase of a complete system, or as a separate item later on.

6.6REPLACEMENT PARTS AND TECHNICAL SPECIFICATIONS

For up-to-date parts breakdowns of any HERO product and/or technical specifications other than those listed in HERO’s literature, please contact your local HERO distributor or HERO directly – we will be pleased to assist you.

HERO Operator’s Manual – Page 22 of 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OPERATOR’S Manual Important Operating Tips Important Read Before UsingSafety Precautions WarrantyContents Hero Hvlp Advantage Unpacking Your Hero System Testing the TurbineTesting the Variable Speed Controller VSC Getting StartedConnecting the Spray GUN and Test Spray Connecting the Hose to the TurbineOperating Instructions and Painting Tips Paint Preparation and Viscosity ChartGeneral Operating Instructions NEEDLE, Fluid TIP and AIR CAP Selection Viscosity ChartIdentifying Needle, Fluid Tip and Air Cap sizes Material To Be Sprayed Time To First Break In StreamMaterial Viscosity Needle and Fluid Tip Needle And Fluid Tip Selection ChartSpray GUN Terminology Surface PreparationOperating the Turbine Air Cap Position Spray Pattern Spray Pattern SelectionTo Begin Spraying Operating the Spray GUNHorizontal Spay Pattern Test Testing Prior to SprayingProblem Solution Basic Spraying Techniques Correct Application Technique Maintaining the Turbine AIR Filters Cleaning and MaintenanceBasic Clean UP When you are finished your spraying projectComplete Disassembly and Cleaning of Spray GUN To Clean And Disassemble The GunTo Clean Parts Individually And Replace Gaskets Replacing the Gland Seal To Replace The Cup Top GasketChanging the NEEDLE, Fluid TIP and AIR CAP Replacing the CUP TOP GasketTo Replace The Gland Seal Problem Probable Cause Solutions Trouble ShootingBasic Troubleshooting Chart Basic Troubleshooting Chart Problem Probable Cause Solutions Troubleshooting Finish Problems CUP-FED Systems Options and AccessoriesVOLUME-FED Systems with BUILT-IN Compressors VOLUME-FED Systems for USE with Shop CompressorsReplacement Parts and Technical Specifications GUN Extension WANDS, TOUCH-UP CUP KIT and Other AccessoriesLimited Warranty Warranty Information
Top Page Image Contents