I.C.T.C. Holdings Corporation 1240 manual Warranty Information, Limited Warranty

Page 24

WARRANTY INFORMATION

LIMITED WARRANTY

HERO Industries warrants to the original purchaser that the HERO equipment described in this manual will be free of defects in materials and workmanship for a period of ONE (1) YEAR from the date of purchase. HERO Industries’ only obligation shall be to repair or replace, at HERO's option, such product proved to be defective during the warranty period. This warranty is subject to the timely notification and substantiation that such products have been stored, maintained and used in accordance with the HERO Industries written instructions. A proof of purchase is required for all warranty claims.

Customers returning goods to HERO Industries or an authorized service center for warranty claims will be asked to prepay freight charges within reason. Goods returned to HERO Industries or an authorized service center for repair or maintenance must be clean and free from paint to allow for inspection. Should any equipment require cleaning, a charge will be made whether or not under warranty. Failure to change filters as needed and the use of parts other than genuine HERO replacement parts that cause damage to the unit will void the warranty.

All statements, technical information and recommendations enclosed are based upon tests that HERO considers reliable. However, neither the seller nor the manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising from the use of the product or the inability to use the product. Before use, users shall determine the suitability of the product for his/her intended use. The user assumes all risk and liability whatsoever in the use or failure to use the product, whether due to a product defect or not. HERO Industries' only obligation shall be to replace or repair, at its option, the quantity of product proved to be defective and any consequential damages shall be limited to the volume of the HERO equipment purchased.

Except where prohibited by law, this warranty is exclusive and is in lieu of all expressed or implied rights, warranties and conditions, statutory or otherwise.

For further information, please contact HERO directly at:

 

Canada (Head Office):

United States (Mailing Only):

2719 Lake City Way

P.O. Box 75

Burnaby, BC Canada

Custer, Washington USA

V5A 2Z6

98240-0075

Tel: (604) 420-6543

Tel: 1-800-494-4376

Fax: (604) 420-8725

 

E-mail:sales@hero.ca

 

Internet: http://www.hero.ca

 

HERO Operator’s Manual – Page 23 of 23

Page 23 Page 24
Image 24
Page 23 Page 24
Contents OPERATOR’S Manual Important Read Before Using Safety PrecautionsWarranty Important Operating TipsContents Hero Hvlp Advantage Testing the Turbine Testing the Variable Speed Controller VSCGetting Started Unpacking Your Hero SystemConnecting the Hose to the Turbine Connecting the Spray GUN and Test SprayPaint Preparation and Viscosity Chart General Operating InstructionsOperating Instructions and Painting Tips Viscosity Chart Identifying Needle, Fluid Tip and Air Cap sizesMaterial To Be Sprayed Time To First Break In Stream NEEDLE, Fluid TIP and AIR CAP SelectionNeedle And Fluid Tip Selection Chart Material Viscosity Needle and Fluid TipSurface Preparation Operating the TurbineSpray GUN Terminology Spray Pattern Selection To Begin SprayingOperating the Spray GUN Air Cap Position Spray PatternTesting Prior to Spraying Problem SolutionHorizontal Spay Pattern Test Basic Spraying Techniques Correct Application Technique Cleaning and Maintenance Basic Clean UPWhen you are finished your spraying project Maintaining the Turbine AIR FiltersTo Clean And Disassemble The Gun To Clean Parts Individually And Replace GasketsComplete Disassembly and Cleaning of Spray GUN To Replace The Cup Top Gasket Changing the NEEDLE, Fluid TIP and AIR CAPReplacing the CUP TOP Gasket Replacing the Gland SealTo Replace The Gland Seal Trouble Shooting Basic Troubleshooting ChartProblem Probable Cause Solutions Basic Troubleshooting Chart Problem Probable Cause Solutions Troubleshooting Finish Problems Options and Accessories VOLUME-FED Systems with BUILT-IN CompressorsVOLUME-FED Systems for USE with Shop Compressors CUP-FED SystemsGUN Extension WANDS, TOUCH-UP CUP KIT and Other Accessories Replacement Parts and Technical SpecificationsWarranty Information Limited Warranty
Top Page Image Contents