Grizzly g0669X owner manual Moving & Placing Base Unit, Moving the Mill Using the Eye Bolt

Page 18

Moving & Placing

Base Unit

The Model G0669X is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment to move the shipping crate and remove the machine from the crate.

The two methods of lifting and moving described below require at least two assistants, and power lifting equipment with a safety hook and chain or lifting straps rated for at least 4000 lbs.

Moving the Mill Using the Eye Bolt

1.Keep the headstock in the same position it was shipped in, similar to Figure 9.

Figure 9. Using the eye bolt to lift the mill.

2.Move the ram so that the eye bolt is aligned with the front edge of the column, then lock the ram in place (refer to Ram Movement on Page 28 for detailed instructions).

3.Attach the safety hook to the lifting eye bolt, then lift the mill slowly to make sure the hook is secure and the mill is lifting evenly. Lift the mill only enough to clear the shipping pallet and floor obstacles.

—If the mill tips in one direction, lower the mill to the ground, then adjust the ram or table to balance the weight. Re-tighten all locks before lifting the mill again.

—If the mill lifts evenly, move it to its perma- nent location.

Note: Have your assistants steady the load as you move it to keep it from swinging.

4.Use a precision level to make sure the table is level. Shim between the base and the floor as necessary to avoid warping or cracking the cast iron base.

Moving the Mill Using Straps

1.Position the head in an upright position, swivel the ram 180°, as shown in Figure 10, then lock it in place (refer to Head Movement on Page 27 and Ram Movement on Page 28 for detailed instructions).

Figure 10. Using lifting straps to lift the mill.

-16-

G0669X Precision 10" x 54" VS Milling Machine

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Left side identificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions For Mills Machine Care and Maintenance220V Single-Phase Operation Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Inventory Figures QtySite Considerations Clean UpPlacement Location Floor LoadMoving the Mill Using the Eye Bolt Moving the Mill Using StrapsMoving & Placing Base Unit Mounting to Shop Floor Bolting to Concrete FloorsAssembly Tools Needed QtyTo assemble the mill Indicator rod installed right side Head shown Test Run Test run consists of verifying the follow- ingTo test run the machine Page Factory adjustments that should be verified Recommended AdjustmentsTo perform the spindle break-in procedure Spindle Break-InOperation Safety Control Panel OperationsTable Movement Table, saddle, and knee locksLongitudinal Power Feed System To operate the longitudinal power feedHead Movement Tilting the HeadRam Movement Rotating the HeadMoving the Ram Forward/Backward Calculating RPM Setting Spindle RPMRotating the Ram Cutting Speeds for High Speed Steel HSS Cutting ToolsSetting Spindle Variable Speed Selecting Spindle Speed RangeDownfeed Controls Coarse Downfeed HandleFine & Auto-Downfeed Components Quill Auto-DownfeedEmergency Spindle Brake Emergency spindle brake on the left Side of the headLoading/Unloading Tooling Loading ToolingUnloading Tooling Accessories H8368-Electric Power DrawbarG1076-52-PC. Clamping Kit G9299-10 Yuasa-Type Rotary Table T20448T20452 T20501 T20456 H0736Maintenance Cleaning ProtectingSchedule Quill Gearing LubricationOne-Shot Oiler Bull & Spindle Speed Range GearingLongitudinal Power Feed Gearing Ram WayVertical Leadscrew Bevel Gears Coolant Reservoir Checking/Adding CoolantTo check/add coolant Changing Coolant To change the coolantDrive Belt Tensioning To check/tension the drive beltService TroubleshootingMotor & Electrical Re-tighten with thread locking fluid Operation Adjusting Gibs Table, Saddle, and Knee GibsAdjusting Backlash To adjust leadscrew backlashPage Electrical Safety Instructions ElectricalG0669X Precision 10 x 54 VS Milling Machine Electrical panel wiring Electrical PanelElectrical Panel Wiring Diagram Upper PanelElectrical Panel Wiring Diagram Lower To Power SupplyControl Panel Control Panel Wiring Diagram Spindle & Vertical Power Feed Motors Feed MotorElectrical Components ThisCoolant Pump Parts Base Machine BreakdownBase Machine Parts List DescriptionSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List One-Shot Oiler Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts ListElectrical Cabinet Breakdown & Parts List Terminal Block 15-POSAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents