Grizzly g0669X owner manual Fine & Auto-Downfeed Components, Quill Auto-Downfeed

Page 34

Fine & Auto-Downfeed Components

There are a number of devices that are used for fine downfeed and quill auto-downfeed control. Use Figure 40 and the descriptions below to understand the functions of these devices.

A

 

 

B

 

 

 

 

 

 

C

J

 

 

D

 

I

 

E

 

 

 

 

 

H

F

 

 

 

 

 

 

G

Figure 40. Fine downfeed and quill auto-

downfeed system components.

A.Auto-Downfeed Rate Selector: Selects one of three auto-downfeed rates.

B.Quill Auto-Downfeed Selector: Changes downfeed control between manual downfeed or auto-downfeed.

C.Quill Dog: Disengages the auto-downfeed clutch lever as it moves with the quill to stop or reverse quill movement.

D.Auto-Downfeed Stop: Sets the maximum depth of the quill.

E.Auto-Downfeed Stop Lock: Locks the auto- downfeed stop in position.

F.Quill Lock: Locks the quill in position.

G.Auto-Downfeed Scale: Shows the posi- tion of the auto-downfeed stop (marked in inches).

H.Auto-Downfeed Clutch Lever: Engages the auto-downfeed gearing to move the quill.

I.Fine Downfeed Handwheel: Moves the quill approximately 1⁄30 of the distance that the coarse downfeed handles moves it.

J.Auto-Downfeed Direction Pin: Starts (in or out), stops (middle), or reverses direction of the quill when in auto-downfeed mode.

Quill Auto-Downfeed

1.Turn the spindle motor OFF, and wait for the spindle to stop.

2.Rotate the quill auto-downfeed selector clock- wise to the ENGAGE (rear) position.

3.Adjust the auto-downfeed stop to the desired depth, then lock it in place.

Note: The increments marked on the auto- downfeed stop represent 0.001" of quill move- ment, with one full revolution equal to 0.010" of quill movement.

4.Move the auto-downfeed direction pin to the center (neutral) position.

Note: The auto-downfeed direction pin has three positions—in, center, and out. Moving the pin to the in or out positions will start or reverse quill movement. Move it to the center position to stop the quill movement.

5.Position the auto-downfeed clutch lever to the right so that the gearing is disengaged.

6.Turn the spindle motor ON and start spindle rotation.

7.Move the auto-downfeed rate selector to the setting that is correct for your operation.

-32-

G0669X Precision 10" x 54" VS Milling Machine

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Identification Left side identificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions For Mills Machine Care and Maintenance220V Single-Phase Operation Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Inventory Figures QtySite Considerations Clean UpPlacement Location Floor LoadMoving the Mill Using Straps Moving the Mill Using the Eye BoltMoving & Placing Base Unit Mounting to Shop Floor Bolting to Concrete FloorsTools Needed Qty AssemblyTo assemble the mill Indicator rod installed right side Head shown Test Run Test run consists of verifying the follow- ingTo test run the machine Page Factory adjustments that should be verified Recommended AdjustmentsTo perform the spindle break-in procedure Spindle Break-InOperation Safety Control Panel OperationsTable Movement Table, saddle, and knee locksLongitudinal Power Feed System To operate the longitudinal power feedHead Movement Tilting the HeadRotating the Head Ram MovementMoving the Ram Forward/Backward Calculating RPM Setting Spindle RPMRotating the Ram Cutting Speeds for High Speed Steel HSS Cutting ToolsSetting Spindle Variable Speed Selecting Spindle Speed RangeDownfeed Controls Coarse Downfeed HandleFine & Auto-Downfeed Components Quill Auto-DownfeedEmergency Spindle Brake Emergency spindle brake on the left Side of the headLoading Tooling Loading/Unloading ToolingUnloading Tooling H8368-Electric Power Drawbar AccessoriesG1076-52-PC. Clamping Kit G9299-10 Yuasa-Type Rotary Table T20448T20452 T20501 T20456 H0736Cleaning Protecting MaintenanceSchedule Quill Gearing LubricationOne-Shot Oiler Bull & Spindle Speed Range GearingRam Way Longitudinal Power Feed GearingVertical Leadscrew Bevel Gears Checking/Adding Coolant Coolant ReservoirTo check/add coolant Changing Coolant To change the coolantDrive Belt Tensioning To check/tension the drive beltTroubleshooting ServiceMotor & Electrical Re-tighten with thread locking fluid Operation Adjusting Gibs Table, Saddle, and Knee GibsAdjusting Backlash To adjust leadscrew backlashPage Electrical Electrical Safety InstructionsG0669X Precision 10 x 54 VS Milling Machine Electrical panel wiring Electrical PanelElectrical Panel Wiring Diagram Upper PanelElectrical Panel Wiring Diagram Lower To Power SupplyControl Panel Control Panel Wiring Diagram Spindle & Vertical Power Feed Motors Feed MotorElectrical Components ThisCoolant Pump Parts Base Machine BreakdownBase Machine Parts List DescriptionSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List One-Shot Oiler Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts ListElectrical Cabinet Breakdown & Parts List Terminal Block 15-POSAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents