Grizzly g0669X owner manual Spindle Break-In, Recommended Adjustments

Page 25

16.Start spindle rotation.

17.Test the variable speed dial by turning the speed all the way up for a few seconds, then turning it all the way down.

18.Point the coolant nozzle onto the table, turn the coolant pump switch to "l" or ON, then check for proper operation of the coolant sys- tem.

19.Use the vertical power feed buttons on the control panel to raise and lower the knee to make sure the vertical limit stops (right side of knee) are working properly.

20.Set the longitudinal limit stops and test the longitudinal power feed for proper operation (see Longitudinal Power Feed on Page 26 for detailed instructions).

When all of the Test Run procedures are success- fully completed, proceed to Spindle Break-In.

Spindle Break-In

NOTICE

Successfully complete the spindle break-in procedure to avoid rapid wear of spindle components when placed into operation.

It is essential to closely follow the proper break-in procedures to ensure trouble-free performance of your mill.

To perform the spindle break-in procedure:

1.After successfully completing the Test Run procedures, make sure the mill is turned OFF and the spindle is stopped.

2.Move the spindle speed range selector to the LOW position (refer to Selecting Spindle Speed Range on Page 30 for detailed instruc- tions).

G0669X Precision 10" x 54" VS Milling Machine

3.Turn the machine ON, start spindle rotation, then adjust the spindle speed dial for approxi- mately 280 RPM.

4.Let the mill run at this speed for 20 minutes, then turn the spindle OFF and wait for it to stop.

5.Use the spindle direction switch on the con- trol panel to reverse the spindle direction and start the spindle rotation, then let the mill run for another 20 minutes.

6.Turn the spindle OFF and wait for it to stop, then move the spindle speed range selector to the HIGH position and start spindle rota- tion.

7.Set the spindle speed at approximately 2100 RPM, then repeat Steps 4–5.

8.Turn the mill OFF. The spindle break-in is now complete and the machine is ready for operation.

Recommended

Adjustments

For your convenience, the adjustments listed below have been performed at the factory.

However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine.

Step-by-step instructions for these adjustments can be found in the SERVICE section starting on Page 43.

Factory adjustments that should be verified:

1.Gib adjustment (Page 46).

2.Leadscrew backlash adjustment (Page 47).

-23-

Image 25
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Left side identification IdentificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Machine Care and Maintenance Additional Safety Instructions For MillsCircuit Requirements 220V Single-Phase OperationSetup Safety SetupItems Needed for Setup UnpackingInventory Figures Qty InventoryPlacement Location Clean UpSite Considerations Floor LoadMoving the Mill Using Straps Moving the Mill Using the Eye BoltMoving & Placing Base Unit Bolting to Concrete Floors Mounting to Shop FloorTools Needed Qty AssemblyTo assemble the mill Indicator rod installed right side Head shown Test run consists of verifying the follow- ing Test RunTo test run the machine Page To perform the spindle break-in procedure Recommended AdjustmentsFactory adjustments that should be verified Spindle Break-InOperations Operation Safety Control PanelTable, saddle, and knee locks Table MovementTo operate the longitudinal power feed Longitudinal Power Feed SystemTilting the Head Head MovementRotating the Head Ram MovementMoving the Ram Forward/Backward Rotating the Ram Setting Spindle RPMCalculating RPM Cutting Speeds for High Speed Steel HSS Cutting ToolsSelecting Spindle Speed Range Setting Spindle Variable SpeedCoarse Downfeed Handle Downfeed ControlsQuill Auto-Downfeed Fine & Auto-Downfeed ComponentsEmergency spindle brake on the left Side of the head Emergency Spindle BrakeLoading Tooling Loading/Unloading ToolingUnloading Tooling H8368-Electric Power Drawbar AccessoriesG1076-52-PC. Clamping Kit T20448T20452 T20501 T20456 H0736 G9299-10 Yuasa-Type Rotary TableCleaning Protecting MaintenanceSchedule One-Shot Oiler LubricationQuill Gearing Bull & Spindle Speed Range GearingRam Way Longitudinal Power Feed GearingVertical Leadscrew Bevel Gears Checking/Adding Coolant Coolant ReservoirTo check/add coolant To change the coolant Changing CoolantTo check/tension the drive belt Drive Belt TensioningTroubleshooting ServiceMotor & Electrical Re-tighten with thread locking fluid Operation Table, Saddle, and Knee Gibs Adjusting GibsTo adjust leadscrew backlash Adjusting BacklashPage Electrical Electrical Safety InstructionsG0669X Precision 10 x 54 VS Milling Machine Electrical Panel Electrical panel wiringPanel Electrical Panel Wiring Diagram UpperTo Power Supply Electrical Panel Wiring Diagram LowerControl Panel Control Panel Wiring Diagram Feed Motor Spindle & Vertical Power Feed MotorsThis Electrical ComponentsCoolant Pump Base Machine Breakdown PartsDescription Base Machine Parts ListSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts List One-Shot Oiler Breakdown & Parts ListTerminal Block 15-POS Electrical Cabinet Breakdown & Parts ListAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.