Grizzly g0669X owner manual

Page 50

7.Use the T-handle 5mm hex wrench to loosen the two cap screws shown in Figure 67.

Adjustment

Plate

Cap Screws

Figure 67. Cross feed leadscrew backlash

adjustment plate and cap screws.

8.Rotate the adjustment plate in small incre- ments, then test the backlash.

Note: To test the backlash, re-install the key and ball handle onto the leadscrew.

9.When you are satisfied with the amount of backlash, re-tighten the adjustment plate cap screws.

10.Make sure that all mating surfaces are clean from debris and oil, then re-install the bearing housing, key, graduated dial assembly, and ball handle.

Note: When re-installing the bearing hous- ing, make sure the way cover mounting flanges (see Figure 66) are on the top for proper alignment.

If the bearing housing does not easily slip onto the alignment pins, use light taps from a dead-blow hammer or wooden mallet evenly on all sides of the housing to gradually seat it against the saddle.

The longitudinal leadscrew backlash is adjusted in the same manner as the cross feed. Refer to Figure 68 for the location of the longitudinal back- lash adjustment plate and cap screws.

Adjustment Plate

and Cap Screws

Figure 68. Longitudinal leadscrew adjustment plate and cap screws as seen from the left side of the table.

-48-

G0669X Precision 10" x 54" VS Milling Machine

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Identification Left side identificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions For Mills Machine Care and Maintenance220V Single-Phase Operation Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Inventory Figures QtySite Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit Moving the Mill Using the Eye BoltMoving the Mill Using Straps Mounting to Shop Floor Bolting to Concrete FloorsTo assemble the mill AssemblyTools Needed Qty Indicator rod installed right side Head shown Test Run Test run consists of verifying the follow- ingTo test run the machine Page Factory adjustments that should be verified Recommended AdjustmentsTo perform the spindle break-in procedure Spindle Break-InOperation Safety Control Panel OperationsTable Movement Table, saddle, and knee locksLongitudinal Power Feed System To operate the longitudinal power feedHead Movement Tilting the HeadMoving the Ram Forward/Backward Ram MovementRotating the Head Calculating RPM Setting Spindle RPMRotating the Ram Cutting Speeds for High Speed Steel HSS Cutting ToolsSetting Spindle Variable Speed Selecting Spindle Speed RangeDownfeed Controls Coarse Downfeed HandleFine & Auto-Downfeed Components Quill Auto-DownfeedEmergency Spindle Brake Emergency spindle brake on the left Side of the headUnloading Tooling Loading/Unloading ToolingLoading Tooling G1076-52-PC. Clamping Kit AccessoriesH8368-Electric Power Drawbar G9299-10 Yuasa-Type Rotary Table T20448T20452 T20501 T20456 H0736Schedule MaintenanceCleaning Protecting Quill Gearing LubricationOne-Shot Oiler Bull & Spindle Speed Range GearingVertical Leadscrew Bevel Gears Longitudinal Power Feed GearingRam Way To check/add coolant Coolant ReservoirChecking/Adding Coolant Changing Coolant To change the coolantDrive Belt Tensioning To check/tension the drive beltMotor & Electrical ServiceTroubleshooting Re-tighten with thread locking fluid Operation Adjusting Gibs Table, Saddle, and Knee GibsAdjusting Backlash To adjust leadscrew backlashPage G0669X Precision 10 x 54 VS Milling Machine Electrical Safety InstructionsElectrical Electrical panel wiring Electrical PanelElectrical Panel Wiring Diagram Upper PanelElectrical Panel Wiring Diagram Lower To Power SupplyControl Panel Control Panel Wiring Diagram Spindle & Vertical Power Feed Motors Feed MotorElectrical Components ThisCoolant Pump Parts Base Machine BreakdownBase Machine Parts List DescriptionSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List One-Shot Oiler Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts ListElectrical Cabinet Breakdown & Parts List Terminal Block 15-POSAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents