Grizzly g0669X owner manual Operation

Page 47

Operation

Symptom

Possible Cause

Possible Solution

Tool slips in collet.

1.

Collet is not fully drawn into spindle taper.

1.

Snug up drawbar.

 

2.

Wrong size collet.

2.

Use correct collet for shank diameter.

3.Debris on collet or spindle mating surface. 3. Remove oil and debris from collet and spindle mating surfaces, then re-install.

 

 

 

 

4.

Excessive depth of cut.

4.

Decrease depth of cut and allow chips to clear.

 

 

 

 

 

Breaking tooling.

1.

Spindle speed/feed rate too fast.

1.

Use correct spindle RPM and feed rate (Page 29).

 

 

 

 

2.

Tooling getting too hot.

2.

Use coolant; reduce spindle RPM/feed rate.

 

 

 

 

3.

Excessive depth of cut.

3.

Decrease depth of cut and allow chips to clear.

 

 

 

 

 

 

 

 

Machine

is

 

loud

1.

Excessive depth of cut.

1.

Decrease depth of cut and allow chips to clear.

when

cutting;

2.

Dull tooling.

2.

Use sharp tooling.

overheats

or

bogs

3.

Feed rate too fast.

3.

Decrease feed rate.

down in the cut.

 

 

 

 

Workpiece

vibrates

1.

Locks not tight.

1.

Tighten all locks on mill that are not associated with

or chatters

during

 

 

 

movement for the operation.

operation.

 

 

 

2.

Workpiece not securely clamped to table or

2.

Check that clamping is tight and sufficient for the

 

 

 

 

 

 

 

 

 

mill vise.

 

operation; make sure mill vise is tight to table.

 

 

 

 

3.

Tooling not secure or is damaged.

3.

Secure tooling; replace if damaged.

 

 

 

 

4.

Spindle speed/feed rate too fast.

4.

Use correct spindle RPM and feed rate (Page 29).

 

 

 

 

5.

Gibs are too loose.

5.

Adjust gibs properly (Page 46).

 

 

 

 

 

Table hard to move.

1.

Locks are tightened down.

1.

Fully loosen locks needed for movement.

 

 

 

 

2.

Chips have loaded up on the ways.

2.

Frequently clean away chips that load up during

 

 

 

 

 

 

 

operations.

 

 

 

 

3.

Ways are dry and in need of lubrication.

3.

Lubricate ways (Page 38).

 

 

 

 

4.

Gibs are too tight.

4.

Adjust gibs properly (Page 46).

 

 

 

 

 

Bad surface finish.

1.

Wrong spindle speed/feed rate.

1.

Use correct spindle RPM and feed rate (Page 29).

 

 

 

 

2.

Dull/damaged tooling; wrong tooling for

2.

Sharpen/replace tooling; use correct tooling for

 

 

 

 

 

operation.

 

operation.

 

 

 

 

3.

Wrong spindle rotation for tooling.

3.

Check for proper spindle rotation for tooling.

 

 

 

 

4.

Workpiece not securely clamped to table or

4.

Check that clamping is tight and sufficient for the

 

 

 

 

 

mill vise.

 

operation; make sure mill vise is tight to table.

 

 

 

 

5.

Gibs are too loose.

5.

Adjust gibs properly (Page 46).

 

 

 

 

 

 

Longitudinal

power

1.

Bevel gear is loose.

1.

Tighten ball handle hex nut.

feed chatters

or

2.

Power feed unit is at fault.

2.

Replace.

grinds on operation.

 

 

 

 

Vertical power

feed

1.

Vertical crank engaged, tripping safety

1.

Disengage vertical crank.

does not work.

 

 

switch.

 

 

 

 

 

 

2.

Safety switch/motor at fault.

2.

Test/repair/replace.

G0669X Precision 10" x 54" VS Milling Machine

-45-

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Left side identification IdentificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Machine Care and Maintenance Additional Safety Instructions For MillsCircuit Requirements 220V Single-Phase OperationUnpacking SetupSetup Safety Items Needed for SetupInventory Figures Qty InventoryFloor Load Clean UpPlacement Location Site ConsiderationsMoving & Placing Base Unit Moving the Mill Using the Eye BoltMoving the Mill Using Straps Bolting to Concrete Floors Mounting to Shop FloorTo assemble the mill AssemblyTools Needed Qty Indicator rod installed right side Head shown Test run consists of verifying the follow- ing Test RunTo test run the machine Page Spindle Break-In Recommended AdjustmentsTo perform the spindle break-in procedure Factory adjustments that should be verifiedOperations Operation Safety Control PanelTable, saddle, and knee locks Table MovementTo operate the longitudinal power feed Longitudinal Power Feed SystemTilting the Head Head MovementMoving the Ram Forward/Backward Ram MovementRotating the Head Cutting Speeds for High Speed Steel HSS Cutting Tools Setting Spindle RPMRotating the Ram Calculating RPMSelecting Spindle Speed Range Setting Spindle Variable SpeedCoarse Downfeed Handle Downfeed ControlsQuill Auto-Downfeed Fine & Auto-Downfeed ComponentsEmergency spindle brake on the left Side of the head Emergency Spindle BrakeUnloading Tooling Loading/Unloading ToolingLoading Tooling G1076-52-PC. Clamping Kit AccessoriesH8368-Electric Power Drawbar T20448T20452 T20501 T20456 H0736 G9299-10 Yuasa-Type Rotary TableSchedule MaintenanceCleaning Protecting Bull & Spindle Speed Range Gearing LubricationOne-Shot Oiler Quill GearingVertical Leadscrew Bevel Gears Longitudinal Power Feed GearingRam Way To check/add coolant Coolant ReservoirChecking/Adding Coolant To change the coolant Changing CoolantTo check/tension the drive belt Drive Belt TensioningMotor & Electrical ServiceTroubleshooting Re-tighten with thread locking fluid Operation Table, Saddle, and Knee Gibs Adjusting GibsTo adjust leadscrew backlash Adjusting BacklashPage G0669X Precision 10 x 54 VS Milling Machine Electrical Safety InstructionsElectrical Electrical Panel Electrical panel wiringPanel Electrical Panel Wiring Diagram UpperTo Power Supply Electrical Panel Wiring Diagram LowerControl Panel Control Panel Wiring Diagram Feed Motor Spindle & Vertical Power Feed MotorsThis Electrical ComponentsCoolant Pump Base Machine Breakdown PartsDescription Base Machine Parts ListSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts List One-Shot Oiler Breakdown & Parts ListTerminal Block 15-POS Electrical Cabinet Breakdown & Parts ListAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents