Grizzly g0669X owner manual To test run the machine

Page 23

To test run the machine:

1.Make sure you understand the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Lubricate the mill, as explained in Lubrication on Page 38.

4.Fill the coolant reservoir (refer to Coolant Reservoir on Page 40 for detailed instruc- tions).

5.Connect the machine to the power source.

6.Make sure the electrical cabinet door is closed and locked, then rotate the main power switch to the ON position (see Figure 21).

Note: The cooling fans on the back of the drive system and electrical cabinet should start.

Main

Power

Switch

Locks

Figure 21. Main power switch on back of

electrical cabinet.

G0669X Precision 10" x 54" VS Milling Machine

7.Push the emergency stop button, then twist it clockwise so it pops out. When the emergen- cy stop button pops out, the switch is reset and ready for operation (see Figure 22).

Note: Refer to Control Panel on Page 24 for additional details.

Spindle

 

Spindle Motor

Motor

OFF

ON

 

 

Spindle

SpindleSpeed

Direction

Emergency

Stop

Coolant

Pump

Figure 22. Control panel.

8.Rotate the spindle speed dial all the way to the left.

9.Push the spindle motor ON button, then turn the spindle direction switch to the left or right to start spindle rotation.

Note: Moving the spindle direction switch to the center or neutral position stops spindle rotation.

Continuous operation of this mill without properly and successfully completing all procedures of the Test Run could lead to personal injury or machine damage, and could void the warranty.

-21-

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Left side identification IdentificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Machine Care and Maintenance Additional Safety Instructions For MillsCircuit Requirements 220V Single-Phase OperationUnpacking SetupSetup Safety Items Needed for SetupInventory Figures Qty InventoryFloor Load Clean UpPlacement Location Site ConsiderationsMoving & Placing Base Unit Moving the Mill Using the Eye BoltMoving the Mill Using Straps Bolting to Concrete Floors Mounting to Shop FloorTo assemble the mill AssemblyTools Needed Qty Indicator rod installed right side Head shown Test run consists of verifying the follow- ing Test RunTo test run the machine Page Spindle Break-In Recommended AdjustmentsTo perform the spindle break-in procedure Factory adjustments that should be verifiedOperations Operation Safety Control PanelTable, saddle, and knee locks Table MovementTo operate the longitudinal power feed Longitudinal Power Feed SystemTilting the Head Head MovementMoving the Ram Forward/Backward Ram MovementRotating the Head Cutting Speeds for High Speed Steel HSS Cutting Tools Setting Spindle RPMRotating the Ram Calculating RPMSelecting Spindle Speed Range Setting Spindle Variable SpeedCoarse Downfeed Handle Downfeed ControlsQuill Auto-Downfeed Fine & Auto-Downfeed ComponentsEmergency spindle brake on the left Side of the head Emergency Spindle BrakeUnloading Tooling Loading/Unloading ToolingLoading Tooling G1076-52-PC. Clamping Kit AccessoriesH8368-Electric Power Drawbar T20448T20452 T20501 T20456 H0736 G9299-10 Yuasa-Type Rotary TableSchedule MaintenanceCleaning Protecting Bull & Spindle Speed Range Gearing LubricationOne-Shot Oiler Quill GearingVertical Leadscrew Bevel Gears Longitudinal Power Feed GearingRam Way To check/add coolant Coolant ReservoirChecking/Adding Coolant To change the coolant Changing CoolantTo check/tension the drive belt Drive Belt TensioningMotor & Electrical ServiceTroubleshooting Re-tighten with thread locking fluid Operation Table, Saddle, and Knee Gibs Adjusting GibsTo adjust leadscrew backlash Adjusting BacklashPage G0669X Precision 10 x 54 VS Milling Machine Electrical Safety InstructionsElectrical Electrical Panel Electrical panel wiringPanel Electrical Panel Wiring Diagram UpperTo Power Supply Electrical Panel Wiring Diagram LowerControl Panel Control Panel Wiring Diagram Feed Motor Spindle & Vertical Power Feed MotorsThis Electrical ComponentsCoolant Pump Base Machine Breakdown PartsDescription Base Machine Parts ListSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts List One-Shot Oiler Breakdown & Parts ListTerminal Block 15-POS Electrical Cabinet Breakdown & Parts ListAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents