Grizzly g0669X owner manual

Page 24

10.Verify that the machine is operating cor- rectly.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always stop the machine and disconnect it from power before inves- tigating or correcting potential problems.

11.Press the emergency stop button to turn the machine OFF, then wait for the spindle to stop on its own.

12.WITHOUT resetting the emergency stop but- ton, press the spindle motor ON button. The machine should not start.

—If the machine does not start, the emer- gency stop button safety feature is working correctly.

—If the machine does start (with the emer- gency stop button pushed in), immediately disconnect power to the machine. The emergency stop button safety feature is not working correctly. This safety feature must work properly before proceeding with regu- lar operations. Call Tech Support for help.

13.Reset the emergency stop button.

To avoid the risk of electrocution during the next step of the Test Run, DO NOT reach into the electrical cabinet.

14.Without reaching into the cabinet, unlock and open the electrical cabinet door approximate- ly 4", then press the spindle motor ON button located on the control panel.

—If the machine does not start, the electrical cabinet safety switch feature is working correctly.

—If the machine does start (with the electri- cal cabinet open), immediately discon- nect power to the machine. The electrical cabinet safety switch feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

15.Close and lock the electrical cabinet door, start the spindle rotating, then push the emer- gency spindle brake (see Figure 23).

—If the machine turns OFF and the spindle stops, the emergency spindle brake is working properly.

—If the machine does not turn OFF or the spindle does not stop, immediately discon- nect power to the machine. The emergency spindle brake safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

Spindle Brake

Safety Switch

Figure 23. Emergency spindle brake.

-22-

G0669X Precision 10" x 54" VS Milling Machine

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Left side identificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2  53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions For Mills Machine Care and Maintenance220V Single-Phase Operation Circuit RequirementsSetup Setup SafetyItems Needed for Setup UnpackingInventory Inventory Figures QtyClean Up Placement LocationSite Considerations Floor LoadMoving the Mill Using the Eye Bolt Moving the Mill Using StrapsMoving & Placing Base Unit Mounting to Shop Floor Bolting to Concrete FloorsAssembly Tools Needed QtyTo assemble the mill Indicator rod installed right side Head shown Test Run Test run consists of verifying the follow- ingTo test run the machine Page Recommended Adjustments To perform the spindle break-in procedureFactory adjustments that should be verified Spindle Break-InOperation Safety Control Panel OperationsTable Movement Table, saddle, and knee locksLongitudinal Power Feed System To operate the longitudinal power feedHead Movement Tilting the HeadRam Movement Rotating the HeadMoving the Ram Forward/Backward Setting Spindle RPM Rotating the RamCalculating RPM Cutting Speeds for High Speed Steel HSS Cutting ToolsSetting Spindle Variable Speed Selecting Spindle Speed RangeDownfeed Controls Coarse Downfeed HandleFine & Auto-Downfeed Components Quill Auto-DownfeedEmergency Spindle Brake Emergency spindle brake on the left Side of the headLoading/Unloading Tooling Loading ToolingUnloading Tooling Accessories H8368-Electric Power DrawbarG1076-52-PC. Clamping Kit G9299-10 Yuasa-Type Rotary Table T20448T20452 T20501 T20456 H0736Maintenance Cleaning ProtectingSchedule Lubrication One-Shot OilerQuill Gearing Bull & Spindle Speed Range GearingLongitudinal Power Feed Gearing Ram WayVertical Leadscrew Bevel Gears Coolant Reservoir Checking/Adding CoolantTo check/add coolant Changing Coolant To change the coolantDrive Belt Tensioning To check/tension the drive beltService TroubleshootingMotor & Electrical Re-tighten with thread locking fluid Operation Adjusting Gibs Table, Saddle, and Knee GibsAdjusting Backlash To adjust leadscrew backlashPage Electrical Safety Instructions ElectricalG0669X Precision 10 x 54 VS Milling Machine Electrical panel wiring Electrical PanelElectrical Panel Wiring Diagram Upper PanelElectrical Panel Wiring Diagram Lower To Power SupplyControl Panel Control Panel Wiring Diagram Spindle & Vertical Power Feed Motors Feed MotorElectrical Components ThisCoolant Pump Parts Base Machine BreakdownBase Machine Parts List DescriptionSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List One-Shot Oiler Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts ListElectrical Cabinet Breakdown & Parts List Terminal Block 15-POSAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents