Grizzly g0669X owner manual Test Run, Test run consists of verifying the follow- ing

Page 22

10.Use the cross feed ball handle to move the table back to the column until you can posi- tion the front way cover on the saddle ways, then secure the cover in place with the five screws shown in Figure 19.

Screws

Figure 19. Front way cover installed.

11.Move the table to the front until you can posi- tion the rear way cover over the saddle and vertical ways, then secure it in place with the four screws shown in Figure 20.

Screws

Figure 20. Rear way cover installed.

-20-

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation.

The test run consists of verifying the follow- ing:

•The motor powers up and runs correctly.

•The emergency stop button safety feature works correctly.

•The electrical cabinet safety switch feature works correctly.

•The emergency spindle brake works cor- rectly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 43.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

Before starting the mill, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to follow this warning could result in serious personal injury or even death!

G0669X Precision 10" x 54" VS Milling Machine

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model G0669X HIGH-PRECISION 10 X VS Milling Machine Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Identification Left side identificationFront identification Right side identification Machine Data Sheet Longitudinal Power Feed Motor Spindle Information  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions For Mills Machine Care and Maintenance220V Single-Phase Operation Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Inventory Figures QtySite Considerations Clean UpPlacement Location Floor LoadMoving the Mill Using Straps Moving the Mill Using the Eye BoltMoving & Placing Base Unit Mounting to Shop Floor Bolting to Concrete FloorsTools Needed Qty AssemblyTo assemble the mill Indicator rod installed right side Head shown Test Run Test run consists of verifying the follow- ingTo test run the machine Page Factory adjustments that should be verified Recommended AdjustmentsTo perform the spindle break-in procedure Spindle Break-InOperation Safety Control Panel OperationsTable Movement Table, saddle, and knee locksLongitudinal Power Feed System To operate the longitudinal power feedHead Movement Tilting the HeadRotating the Head Ram MovementMoving the Ram Forward/Backward Calculating RPM Setting Spindle RPMRotating the Ram Cutting Speeds for High Speed Steel HSS Cutting ToolsSetting Spindle Variable Speed Selecting Spindle Speed RangeDownfeed Controls Coarse Downfeed HandleFine & Auto-Downfeed Components Quill Auto-DownfeedEmergency Spindle Brake Emergency spindle brake on the left Side of the headLoading Tooling Loading/Unloading ToolingUnloading Tooling H8368-Electric Power Drawbar AccessoriesG1076-52-PC. Clamping Kit G9299-10 Yuasa-Type Rotary Table T20448T20452 T20501 T20456 H0736Cleaning Protecting MaintenanceSchedule Quill Gearing LubricationOne-Shot Oiler Bull & Spindle Speed Range GearingRam Way Longitudinal Power Feed GearingVertical Leadscrew Bevel Gears Checking/Adding Coolant Coolant ReservoirTo check/add coolant Changing Coolant To change the coolantDrive Belt Tensioning To check/tension the drive beltTroubleshooting ServiceMotor & Electrical Re-tighten with thread locking fluid Operation Adjusting Gibs Table, Saddle, and Knee GibsAdjusting Backlash To adjust leadscrew backlashPage Electrical Electrical Safety InstructionsG0669X Precision 10 x 54 VS Milling Machine Electrical panel wiring Electrical PanelElectrical Panel Wiring Diagram Upper PanelElectrical Panel Wiring Diagram Lower To Power SupplyControl Panel Control Panel Wiring Diagram Spindle & Vertical Power Feed Motors Feed MotorElectrical Components ThisCoolant Pump Parts Base Machine BreakdownBase Machine Parts List DescriptionSpanner NUT Drive System Breakdown Drive System Parts List Head Breakdown Head Parts List Angular Bearing 7207C Longitudinal & Cross Slide Leadscrews Breakdown & Parts List One-Shot Oiler Breakdown & Parts List Control Panel Electrical Components Breakdown & Parts ListElectrical Cabinet Breakdown & Parts List Terminal Block 15-POSAccessories Breakdown & Parts List Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Related manuals
Manual 13 pages 33.37 Kb

g0669X specifications

The Grizzly G0669X is a powerful and versatile tool designed for woodworkers and enthusiasts who demand precision and efficiency in their projects. This impressive machine combines advanced technology with user-friendly features to deliver superior performance, making it a standout choice for both hobbyists and professionals alike.

At the heart of the G0669X is its 3HP motor, which provides substantial power for a range of applications, from milling to crafting intricate designs. The robust motor enables the machine to handle various materials, including hardwoods and softwoods, effortlessly delivering clean and accurate cuts with every pass. Its table size is designed to offer ample workspace, allowing users to tackle larger projects without the need for constant repositioning.

One of the standout features of the G0669X is its digital readout. This advanced technology offers precise measurements and helps users achieve the exact specifications required for their projects. The readout improves efficiency and accuracy, reducing the margin for error and enhancing the overall quality of the work produced.

Another essential characteristic of the G0669X is its impressive range of speeds. With multiple speed settings, users can easily select the optimum speed for various tasks, whether it’s planing, joinery, or creating decorative edges. This versatility makes the G0669X an invaluable addition to any workspace, allowing it to adapt to the diverse needs of different projects.

The machine also features a heavy-duty cast iron construction, ensuring stability and durability during operation. The sturdy base minimizes vibrations, which contributes to smoother cuts and better overall performance. Additionally, the precision-ground table surface enhances the accuracy of cuts while providing a reliable and flat platform for workpieces.

Safety is a top priority for the Grizzly G0669X, which includes various safety features designed to protect users during operation. This includes emergency shut-off switches and blade guards, ensuring that users can work confidently and safely.

In conclusion, the Grizzly G0669X stands out in the world of woodworking machinery for its powerful motor, advanced digital readout, versatile speed settings, and robust construction. This machine brings precision, efficiency, and safety to the forefront, making it a go-to option for anyone looking to elevate their woodworking experience. Whether you are a seasoned professional or a passionate hobbyist, the G0669X is sure to meet and exceed your expectations, delivering exceptional results for every project.
Top Page Image Contents