Bosch Power Tools PS32-02, PS32BN, PS22-02, PS22BN manual Assembly

Page 9
! WARNING

2610031969 09-13_2610031969 09-13.qxp 10/3/13 10:50 AM Page 9

Assembly

Disconnect battery pack ! WARNING from tool before making

any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

INSERTING BITS (Model PS32 only)

Move reverse switch lever to the center “OFF” position. Remove battery pack and rotate the clutch ring to the drill bit symbol

”. Rotate the chuck sleeve counter- clockwise viewing from chuck end, and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small bits, or as far as it will go for large bits. Close chuck by rotating the chuck sleeve clockwise and securely tighten by hand (Fig. 3).

Do not use the power of the ! WARNING drill while grasping chuck

to loosen or tighten bit. Friction burn or hand injury is possible if attempting to grasp the spinning chuck.

FIG. 3

CHUCK SLEEVE

 

DRILL BIT

 

BIT HOLDER

SCREWDRIVER BIT

The Bosch model PS22 Cordless Drill/Driver has a chuck that accepts any 1/4" hex bit.

INSERTING AND REMOVING ACCESSORIES

(Model PS22 only)

To avoid loss of control, ensure bit is locked in chuck

by pulling on bit after it has been inserted.

To insert an accessory, simply pull locking sleeve forward, insert desired accessory into chuck until the locking sleeve retracts automatically, locking the bit (Fig. 2).

To remove an accessory, pull locking sleeve forward and simply remove it from the chuck.

One inch bits should only be used along with a bit holder as shown in figure 2.

FIG. 4

LOCKING

SLEEVE

HEX-SHANK

DRILL BIT

SCREWDRIVER

CHUCK

BIT

 

 

BIT HOLDER

BELT CLIP AND BIT TIP HOLDER”

Both the PS22 and PS32 come with the option of a metal belt clip and a four piece bit tip holder.

BELT CLIP

When the tool is attached to ! WARNING the belt, position yourself to

avoid entanglement with surrounding objects. Unexpected entanglement could cause the tool to fall resulting in injury to the operator or bystanders.

The belt clip will allow you to conveniently attach your tool to your belt. This feature will allow you to have both hands free when climbing a ladder or moving to another work area.

The belt clip can be attached to either side of the tool by securing it with a mounting screw. Always make sure you securely tighten the mounting screw before use (Fig. 5).

To use clip, turn tool upside down and attach to your belt.

-9-

Image 9
Contents Leer antes de usar Read Before UsingSee Ver la páginaWork area safety General Power Tool Safety WarningsElectrical safety Personal safetySafety Rules for Cordless Drill/Drivers Battery tool use and careService Additional Safety Warnings Name Designation/Explanation SymbolsSymbols Cordless Drill/Driver Functional Description and SpecificationsMaximum Capacities Rubberized Grip Battery Release TabsAssembly Operating Instructions Variable Speed Controlled Trigger SwitchProtection Against Deep Discharging BrakeOperating Tips Driving with Variable Speed Drilling with Variable SpeedFastening with Screws Drill BitsCleaning MaintenanceSécurité électrique Sécurité du lieu de travailUtilisation et entretien des outils Électroportatifs Consignes de sécurité pour perceuses/tournevis sans cordonUtilisation et entretien des outils à piles EntretienLe plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesSymboles suite Perceuse/visseuse sans fil Description fonctionnelle et spécificationsPS22 Tension nominale Assemblage Consignes de fonctionnement Embrayage Reglable Changement DE VitessesÉclairage D’APPOINT Intégré Témoins Détat DE Charge DES PilesEnfoncement À Vitesse Variable Perçage À Vitesse VariableFixation À L’AIDE DE VIS ForetsEntretien Cordons de rallongeNettoyage Seguridad del área de trabajo Seguridad eléctricaUso y cuidado de las herramientas Mecánicas Servicio de ajustes y reparaciones Uso y cuidado de las herramientas Alimentadas por bateríasAdvertencias de seguridad adicionales Símbolo Nombre Designación/explicación SímbolosSímbolos continuación Taladro/destornillador sin cordón Descripción funcional y especificacionesCambiador DE Engranajes Clip DE Cinturón Y Ensamblaje Interruptor Gatillo DE Velocidad Variable Controlada Instrucciones de funcionamientoFreno Palanca DE AVANCE/INVERSIÓN Y Cierre DEL GatilloConsejos de funcionamiento Brocas Para Taladro Sujecion CON TornillosTaladrado DE Madera Taladrado DE MetalCordónes de extensión MantenimientoServicio Limpieza2610031969 09-132610031969 09-13.qxp 10/3/13 1050 AM Remarques Notas 2610031969