Craftsman 706.59669, 706.59668 owner manual Count, Function

CONNECTING POWER

•Ensure that the unit and power cord are clean and dry.

•insert the round end of the power cord connector into the jack in the back of the unit.

•Plug the cord into an appropriate electrical outlet.

Fuse block

Jack

Cord

REMOVING AND INSTALLING

DRAWERS:

•Empty the drawer.

•Fully extend the drawer.

Release

Lever Style - Lift or lower (depending on the slide) the release lever

on both sides, (this allows the slides to ride

over the stops.) Pull out to remove.

Tab Style - Depress the release tabs on both sides, (this allows the slides to ride over the stops.) Pull out to remove.

To reinstall, carefully align the slides and

push the drawer into the unit until the drawer stops.

INFORMATION CENTER

OPERATION

The information center is equipped with a battery backup to maintain memory only. The display will not function while power is disconnected from the unit.

Outside temperature display requires optional outside temperature sensor.

Display		backlight
•	Pressing		_		turns		the	display
	backlight on for 15 seconds.
Setting		the	current		time
•	Press	and		hold _				for at least
	two seconds. (Second resets to zero
	and hour		begins		to flash.)
•	Press	_		to	set	am/pm			or 24 hour
	mode as desired. Note: The am/pm
	indicator is not shown in 24 hour
	mode.
•	Adjust	hour		using	(_	and		(_.
•	Pressing		_		toggles			to	next field.
	Note: To toggle to minute without
	changing hour, press _) then (_ then
•	Adjust	minute using				(_	and		(_.
•	Press	_		to toggle			to	next field.

•Repeat to adjust Month, Day, and Year.

•Toggling past year exits set mode.

•Day of week is displayed according to Month, Day, and Year.

Temperature				Display
Pressing		_			toggles		inside			and
outside		temperature				displays			between
Celsius		and		Fahrenheit.
•	Pressing		_		toggles			inside and
	outside		temperature				displays			between
	ACT		(Actual		temperature)
	MIN		(Minimum			recorded
	temperature				since		last		reset)
	MAX		(Maximum			recorded
	temperature				since		last		reset)
•	Press	and		hold	_			for	at	least two
	seconds to clear inside and outside
	minimum			and	maximum			recorded
	temperatures.

•An audible beep will sound when temperature is reset.

Setting the alarm

• Press and hold _for at least two seconds. (Second resets to zero and hour begins to flash.)

•Adjust hour using (_ and (_).

• Pressing _ toggles to next field.

•Repeat to adjust minute.

•Toggling past minute exits set mode.

Turning alarm on or off

When the alarm is activated, the display will show the indicator _,.

•	Press	_	to	activate	or deactivate
	the alarm.
•	Press	_	to	silence	alarm when
	ringing.

Time \

•\\

oF_eoCP_ D

Clock Set

Alarm Set-_

(+)

Temp Inside

(-)

Timer function
•	Press	_	to enter timer mode.
•	Press	_	to start timer.
•	Each	time _	is pressed starts

	or stops timer.
•	Press	and hold _				for	at least
	two seconds		to	reset	timer	to	zero.
Count		down	timer	function
•	Press	and	hold	_	for	at	least two

seconds.

•Display shows O0:O0:O0 and hour begins to flash.

•Adjust hour using @ and @.

•Pressing @ toggles to next field.

•Repeat to adjust minute and second.

•Toggling past second exits set mode. Note: To set timer to 24 hours, toggle display to 00:00:0O.

•	Press	_	to start count	down.
•	Each	time _	is pressed	starts
	or stops timer.

•Alarm sounds when timer reaches 0O:00:OO.

•Press any button to silence the alarm.

Clock

When in Timer or Count down timer

mode,	press	_	to	display	current
time.	Press	_	to	return to	timer or
count	down	timer.

Alarm

AM/PMActivated

jTimer

Start/Stop

Clock

Alarm

\\

\ \Light

Date Temp outside (Accessory required)

5 6