Ryobi P240 manuel dutilisation To INSTALL/REMOVE Battery Pack, Switch Trigger, Variable Speed

Page 9

OPERATION

TO INSTALL/REMOVE BATTERY PACK

See Figure 2, page 12.

WARNING:

Always remove battery pack from your tool when you are assembling parts, making adjustments, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury.

To install:

Place the battery pack in the tool. Align the raised rib on the battery pack with groove in the battery port.

Make sure the latches on each side of the battery pack snap in place and that the battery pack is secured in the tool before beginning operation.

To remove:

Depress the latches on both sides of the battery pack to release the battery pack and remove it from the tool.

WARNING:

Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or car- rying at your side.

CAUTION:

To prevent gear damage, always allow chuck to come to a complete stop before changing the direction of rotation.

To stop the drill, release switch trigger and allow the chuck to come to a complete stop.

NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right.

Avoid running the drill at low speeds for extended periods of time. Running at low speeds under constant usage may cause the drill to become overheated. If this occurs, cool the drill by running it without a load and at full speed.

KEYLESS CHUCK

See Figure 4, page 12.

The drill has a keyless chuck to tighten or release drill bits in the chuck jaws. The arrows on the chuck indicate which direction to rotate the chuck body in order to LOCK (tighten) or UNLOCK (release) the drill bit.

Grasp and hold the collar of the chuck with one hand. Ro- tate the chuck body with your other hand. This chuck has a racheting design that allows the user to hear a series of “clicks” while tightening the jaws. This “clicking” will stop once the chuck and jaws are secure.

SWITCH TRIGGER

See Figure 3, page 12.

To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger.

VARIABLE SPEED

This tool has a variable speed switch trigger that delivers higher speed with increased trigger pressure. Speed is con- trolled by the amount of switch trigger depression.

NOTE:  You might hear a whistling or ringing noise from the switch during use. Do not be concerned; this is a normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3, page 12.

The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for forward drilling. The drilling direction is reversed when the selector is to the right of the switch trigger.

Setting the direction of rotation selector in the OFF (center lock) position helps reduce the possibility of accidental start- ing when not in use.

WARNING:

Do not hold the chuck body with one hand and use the power of the drill to tighten the chuck jaws on the drill bit. The chuck body could slip in your hand or your hand could slip and come in contact with rotating drill bit. This could cause an accident resulting in serious personal injury.

INSTALLING/REMOVING BITS

See Figures 4 - 5, page 12.

To install:

Lock the switch trigger by placing the direction of rotation selector in the center position.

Open or close the chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws.

Insert the drill bit.

9 – English

Image 9
Contents Save this Manual for Future Reference OPERATOR’S ManualTable of Contents WarrantyIntroduction Work Area Safety General Power Tool Safety WarningsElectrical Safety Personal SafetyService Battery Tool USE and CareCalifornia Proposition Drill Safety WarningsName DESIGNATION/EXPLANATION SymbolsFeatures Operation AssemblySwitch Trigger To INSTALL/REMOVE Battery PackINSTALLING/REMOVING Bits Variable SpeedDrilling Using Swiveling Battery FootWood DRILLING METAL DRILLINGGeneral Maintenance MaintenanceTo Retighten a Loose Chuck See Figures 8 10,Garantie Table DES MatièresRègles DE Sécurité Relatives AUX Outils Électriques Dépannage Utilisation ET Entretien DE LA PileProposition 65 DE LA Californie Avertissement Avertissements DE Sécurité Relatifs PERCEUSE-TOURNEVISSymbole Signal Signification SymbolesSymbole NOM Désignation / Explication AVERTISSEMENT Caractéristiques Utilisation AssemblageDéballage Liste DE ContrôleINSTALLATION/ Retrait DES Embouts RETRAIT/INSTALLATION DU BLOC-PILES Gâchette DE Commutateur Vitesse VariablePerçage DU Bois Usage DU BLOC-PILES PivotantPerçage Perçage DU Métal RetraitEntretien Général EntretienSerrage D’UN Mandrin Desserré Retrait DU MandrinIntroducción Índice DE ContenidoGarantía 12-13Advertencia Advertencias DE Seguridad Para Herramientas EléctricasSeguridad Personal Seguridad EléctricaEmpleo Y Cuidado DE LA Herramienta Eléctrica Empleo Y Cuidado DE LA Herramienta DE BateríasServicio California Propuesta DE LEY NÚM Advertencia Advertencias DE Seguridad TALADRO-DESTORNILLADORPeligro SímbolosPrecaución Símbolo Señal SignificadoCaracterísticas Funcionamiento ArmadoDesempaquetado Lista DE EmpaquetadoINSTALACIÓN/ Remoción DE LAS Brocas Vea la figura 4,Vea las figuras 4 y 5, PIE Giratorio Para EL Paquete DE Baterías TaladradoTaladrado EN Madera Taladrado EN MetalMantenimiento General MantenimientoPara Apretar EL Portabrocas Cuando SE Afloje Desmontaje DEL PortabrocasRight / Correct / Forma Correcta Chuck jaws mors du mandrin, mordazas del Page Page OPERATOR’S Manual / 18 Volt Right Angle Drill
Related manuals
Manual 18 pages 38.54 Kb

P240 specifications

The Ryobi P240 is a versatile and highly efficient 18V cordless drill/driver that stands out in the power tool market for both professionals and DIY enthusiasts. It combines advanced features and technologies that enhance performance, making it suitable for various drilling and driving applications.

One of the most notable features of the Ryobi P240 is its impressive motor, which delivers up to 1,600 RPM. This high-speed performance allows users to tackle a wide range of materials, including wood, metal, and plastic. The drill offers a 24-position clutch, enabling precise torque control to prevent overdriving screws or damaging softer materials. This level of customization makes the P240 a reliable choice for both delicate tasks and heavy-duty applications.

The P240’s lightweight and compact design is another significant advantage. Weighing only 3.5 pounds and designed with an ergonomic grip, it minimizes user fatigue during extended use. Its balanced weight distribution adds to user comfort, allowing for easy maneuverability in tight spaces.

This drill is powered by Ryobi’s 18V ONE+ battery system, offering compatibility with over 225 other Ryobi tools. Users can easily swap batteries, providing flexibility and convenience for continuous work without downtime. The P240 benefits from Ryobi’s advanced lithium-ion technology, which ensures longer runtime and improved battery performance.

Another key feature is the integrated LED work light that illuminates dark work areas. This addition enhances visibility, making it easier to work in dimly lit or hard-to-reach locations. The P240 also includes a keyless chuck that allows for quick and easy bit changes, which is particularly beneficial when switching between tasks.

For those looking for versatility, the Ryobi P240 comes with a 3/8-inch single sleeve keyless chuck that accommodates various drill bits. Whether you're drilling holes or driving screws, this drill provides the flexibility needed for diverse applications.

In summary, the Ryobi P240 is a well-rounded cordless drill that combines power, portability, and precision. With its robust motor, adjustable clutch, lightweight design, and compatibility with Ryobi's 18V ONE+ system, this drill is an excellent choice for anyone looking to enhance their toolkit with a reliable and efficient drilling solution.