How to Reset Icom IC-R5 Radio | Icom Radio Programming Instructions

10 OTHER FUNCTIONS

■ Partial reset

AT POWER ON

If you want to initialize the operating conditions (VFO fre- quency, VFO settings, set mode contents) without clearing the memory contents, a partial resetting function is available for the receiver.

➥While pushing [FUNC] and [TS•SET], turn the power ON to partially reset the receiver.

[FUNC]

[TS•SET]

[PWR]

■ All reset

AT POWER ON

The function display may occasionally display erroneous in- formation (e.g. when first applying power). This may be caused externally by static electricity or by other factors.

If this problem occurs, turn power OFF. After waiting a few seconds, turn power ON again. If the problem persists, per- form the following procedure.

•Partial resetting is also available. See left for details.

IMPORTANT!:

Resetting the receiver CLEARS all memory information

and initializes all values in the receiver, including TV chan- nel skip setting.

➥While pushing [FUNC] and [V/M•S.MW•~], turn the power ON to reset the CPU.

[FUNC]

FM

P SKIP

[V/M•S.MW•~] [PWR]

*The appearing frqeuency is differ according to receiver version.

53

Image 64

Icom IC-R5 instruction manual Partial reset

Contents

IR5 Explicit Definitions Precaution Supplied Accessories Iii Table of Contents Battery installation Quick Reference GuidePreparation Belt clip Rotate Dial to select Y then push Band Install the Ni-Cd batteriesCharging conﬁrmation is displayed as below Your ﬁrst scanning Experience About default settingBasic operation Receive mode selection Setting frequencyMemory programming Selecting a memory Channel Programmed scan operation Programming scan edgesSelecting a scan edge channel a Selecting a scan edge channel B Starting scan Select VFO mode Cancelling scanSelecting a scanning type Starting scan Panel Description Front, top and side panels Push for 1 sec. to turn the receiver power on and OFF UCONTROL Dial Dial WLOCK Indicator p ERECEIVE Mode Indicator pRDUPLEX Indicators p TTONE Indicators 1SIGNAL Strength Indicator p Priority Watch Indicator p2VOLUME Exchange Indicator p Battery Charging Battery installationBattery caution Charging caution Battery charging Charging connectionsCharging description Charging periods Approx hours VFO and memory channels Frequency and Channel SettingOperating band selection Frequency and Channel Setting Available frequency bands Setting a frequency Setting a tuning stepTuning step selection Rotate Dial to select the desired frequency band Push V/MS.MW~ to select the memory mode Selecting a memory channelLock function Rotate Dial to select the desired memory channel Setting audio volume When a signal is receivedBasic Operation Receiving Squelch level setting Receive mode selection Attenuator function Monitor functionPush and hold SQL to monitor the operating frequency Duplex operation SettingRotate Dial to select DUP Push Tsset momentarily to exit set mode Setting dial select stepDial select step Memory Channels General description Rotate Dial to select the desired bank channel number Memory bank settingPush V/MS.MW~ momentarily to set the channel into the bank Memory bank selection Push V/MS.MW~ to select memory mode, if desiredRotate Dial to select the bank channel To return to regular memory condition, rotate Dial while Rotate Dial to move the cursor to left or right Programming memory/bank nameAvailable characters Selecting display type Selecting bank channel indication Copying memory contents Push V/MS.MW~ for 1 sec. to clear the contents Memory clearingWhile pushing FUNC, push V/MS.MW~ for 1 sec Essary Transferring memory contents Erasing/transferring bank contents Scan Operation Scan typesFull Scan p FREQUENCY/MEMORY Skip Function p Full/band/programmed scan Select VFO mode with V/MS.MW~To start the scan, push Modescan Scan edges programming Example Programming 145.300 MHz into scan edges 03A Select memory mode with V/MS.MW~ Memory/bank/all bank scan Auto memory write scan During auto-memory write scanningRe-calling the stored frequencies Clearing the stored frequencies Skip channel/frequency setting Nel Scan resume timer Scan pause timerScan resume condition Priority Watch Priority watch typesAbout priority beep function Watch starts Push Tsset to exit set mode and start the watch Push Tsset to cancel the watchPriority watch operation Select memory mode, or the desired bank group then When scanning memory/bank channels VFO scan watch qSelect memory mode0Push Tsset to cancel the watch and scan Tone Squelch and Pocket Beep Tone/DTCS squelch operationOPush Func to stop the beeps and blinking manually Step y Available Dtcs code list Tone squelch frequency/DTCS code settingAvailable tone frequency list Dtcs polarity setting Tone scan While pushing FUNC, push Modescan to start the tone scan SET Mode Set mode entering and operationExpanded set mode ON/OFF General General set mode items Set mode itemsExpanded set mode items Dial select step Priority watchKey-touch beep Beep output level Antenna selection Power saveMHz differ according to version, re Monitor switch action No accessible switch is available, exceptKey lock effect Dial speed acceleration Auto power OFF Scan pause timerScan resume timer Scan stop beep Duplex direction Offset frequencyTone squelch DTone frequency Ddtcs code Dtcs polarityAvailable subaudible tone frequencies Available Dtcs code Weather alert function LCD contrastTurns weather alert function on and OFF Antenna selection Other FunctionsSelecting antenna Weather channel operation Dial function assignmentWeather channel selection Turn the weather alert function OFF in set mode Cloning between receivers Push SQL on the master receiver Cloning using a personal computer Auto power-off functionCloning error Partial reset Frequency Table TV channelsDU.S.A. channels Dccir channels DChina channels DNewZealand Channels Indonesian channels DItalian channelsTaiwan channels FOT channels VHF marine channels Weather channelsunit MHz Murs channels Other communications in the USAHF CB Citizens Band channels General aviation frequencies Wireless MicrophonesDCable TV IRC Other communications- other countries LPD Low Power Device channels Unit MHzPMR446 channels unit MHz UHF C.R.S Citizen Radio Service channels Maintenance Troubleshooting CP-18A/E fuse replacement Specifications Dgeneral Options Options Pocket Guide Memory channel programming Declaration Conformity We Icom Inc. Japan Kamiminami, Hirano-ku, Osaka 547-0003 Japan