Maintenance, Troubleshooting | Icom IC-R5 specs

MAINTENANCE 12

■ Troubleshooting				If your receiver seems to be malfunctioning, please check the
■ Troubleshooting				following points before sending it to a service center.
				following points before sending it to a service center.

PROBLEM			POSSIBLE CAUSE		SOLUTION				REF.
No power comes on.			• The batteries are exhausted.		• Replace the batteries or charge the batteries.				pgs. 5, 6
			• The battery polarity is reversed.		• Check the battery polarity.				p. 5

No sound comes from the			• Volume level is too low.		• Push [Y] to obtain a suitable level.				p. 11
speaker.			• Squelch level is set too tight.		• While pushing [SQL], rotate [DIAL] to set the				p. 12
					squelch level.
			• Different tone is selected with tone squelch.		• Turn the appropriate function OFF.				p. 35

Sensitivity is low and only			• Attenuator function is activated.		• While pushing [FUNC], push [SQL] to urn the at-				p. 13
strong signals are audible.					tenuator function OFF.

Frequency cannot be set.			• The lock function is activated.		• While pushing [FUNC], push [BAND•		] for		p. 10
Frequency cannot be set.			• The lock function is activated.		• While pushing [FUNC], push [BAND•		] for		p. 10
					1 sec. to turn the function OFF.

No beep sound.			• Beep tones are turned OFF or the beep tone level		• Turn beep tone ON or set the beep tone level to ap-				p. 41
			is too low.		propriate level in set mode.

Receive audio is distorted.			• The operating mode is not selected correctly.		• Push [MODE•SCAN] several times to select a suit-				p. 12
					able operating mode.

Desired set	mode	item	• “EXPAND” item is set to OFF.		• Turn “EXPAND” item ON.				p. 39
cannot be selected.			• Some set mode items can be selected in the AM		• Choose the AM or FM broadcast band.				p. 7
			or FM broadcast band only.

Programmed	scan	does	• Program scan edges are not programmed.		• Program a pair of scan edge channels.				p. 27
not start.

Memory or	bank	scan	• No or only one memory or bank channel is pro-		• Program at least 2 memory or bank channels				pgs. 16,
does not start.			grammed.						17

Installed batteries cannot			• The batteries over discharged.		• Re-install the batteries (wait at least for 1 sec.),				p. 6
be charged.					then plug the AC adapter while pushing [FUNC].

11

12

62

Image 73

Icom IC-R5 instruction manual Maintenance, Troubleshooting

Contents

IR5 Explicit Definitions Precaution Iii Supplied Accessories Table of Contents Quick Reference Guide Battery installationPreparation Belt clip Rotate Dial to select Y then push Band Install the Ni-Cd batteriesCharging conﬁrmation is displayed as below Your ﬁrst scanning Experience About default settingBasic operation Setting frequency Receive mode selectionMemory programming Selecting a memory Channel Programming scan edges Programmed scan operationSelecting a scan edge channel a Selecting a scan edge channel B Cancelling scan Starting scan Select VFO modeSelecting a scanning type Starting scan Front, top and side panels Panel Description UCONTROL Dial Dial Push for 1 sec. to turn the receiver power on and OFF ERECEIVE Mode Indicator p WLOCK Indicator pRDUPLEX Indicators p TTONE Indicators 1SIGNAL Strength Indicator p Priority Watch Indicator p2VOLUME Exchange Indicator p Battery installation Battery ChargingBattery caution Charging caution Charging connections Battery chargingCharging description Charging periods Approx hours VFO and memory channels Frequency and Channel SettingOperating band selection Available frequency bands Frequency and Channel Setting Setting a tuning step Setting a frequencyTuning step selection Rotate Dial to select the desired frequency band Selecting a memory channel Push V/MS.MW~ to select the memory modeLock function Rotate Dial to select the desired memory channel When a signal is received Setting audio volumeBasic Operation Receiving Receive mode selection Squelch level setting Attenuator function Monitor functionPush and hold SQL to monitor the operating frequency Duplex operation SettingRotate Dial to select DUP Push Tsset momentarily to exit set mode Setting dial select stepDial select step General description Memory Channels Rotate Dial to select the desired bank channel number Memory bank settingPush V/MS.MW~ momentarily to set the channel into the bank Push V/MS.MW~ to select memory mode, if desired Memory bank selectionRotate Dial to select the bank channel To return to regular memory condition, rotate Dial while Rotate Dial to move the cursor to left or right Programming memory/bank nameAvailable characters Selecting bank channel indication Selecting display type Copying memory contents Memory clearing Push V/MS.MW~ for 1 sec. to clear the contentsWhile pushing FUNC, push V/MS.MW~ for 1 sec Essary Transferring memory contents Erasing/transferring bank contents Scan types Scan OperationFull Scan p FREQUENCY/MEMORY Skip Function p Full/band/programmed scan Select VFO mode with V/MS.MW~To start the scan, push Modescan Example Programming 145.300 MHz into scan edges 03A Scan edges programming Memory/bank/all bank scan Select memory mode with V/MS.MW~ During auto-memory write scanning Auto memory write scanRe-calling the stored frequencies Clearing the stored frequencies Nel Skip channel/frequency setting Scan resume timer Scan pause timerScan resume condition Priority watch types Priority WatchAbout priority beep function Watch starts Push Tsset to cancel the watch Push Tsset to exit set mode and start the watchPriority watch operation Select memory mode, or the desired bank group then When scanning memory/bank channels VFO scan watch qSelect memory mode0Push Tsset to cancel the watch and scan Tone/DTCS squelch operation Tone Squelch and Pocket BeepOPush Func to stop the beeps and blinking manually Step y Available Dtcs code list Tone squelch frequency/DTCS code settingAvailable tone frequency list Dtcs polarity setting While pushing FUNC, push Modescan to start the tone scan Tone scan Set mode entering and operation SET ModeExpanded set mode ON/OFF General General set mode items Set mode itemsExpanded set mode items Priority watch Dial select stepKey-touch beep Beep output level Antenna selection Power saveMHz differ according to version, re No accessible switch is available, except Monitor switch actionKey lock effect Dial speed acceleration Scan pause timer Auto power OFFScan resume timer Scan stop beep Duplex direction Offset frequencyTone squelch Dtcs polarity DTone frequency Ddtcs codeAvailable subaudible tone frequencies Available Dtcs code Weather alert function LCD contrastTurns weather alert function on and OFF Antenna selection Other FunctionsSelecting antenna Weather channel operation Dial function assignmentWeather channel selection Turn the weather alert function OFF in set mode Push SQL on the master receiver Cloning between receivers Cloning using a personal computer Auto power-off functionCloning error Partial reset TV channels Frequency TableDU.S.A. channels Dccir channels DNew DChina channelsZealand Channels DItalian channels Indonesian channelsTaiwan channels FOT channels Weather channelsunit MHz VHF marine channels Murs channels Other communications in the USAHF CB Citizens Band channels General aviation frequencies Wireless MicrophonesDCable TV IRC Other communications- other countries LPD Low Power Device channels Unit MHzPMR446 channels unit MHz UHF C.R.S Citizen Radio Service channels Troubleshooting Maintenance CP-18A/E fuse replacement Dgeneral Specifications Options Options Pocket Guide Memory channel programming We Icom Inc. Japan Declaration Conformity Kamiminami, Hirano-ku, Osaka 547-0003 Japan