Declaration Conformity, We Icom Inc. Japan

CE 16

DECLARATION

OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku

Osaka 547-0003, Japan

Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed.

Kind of equipment:

COMMUNICATIONS RECEIVER

Type-designation: iR5

Version (where applicable):

This compliance is based on conformity with the following harmonised standards, speciﬁcations or documents:

i)Article 3.1a EN 60950: 1992+A11

ii)Article 3.1b EN 301489-1 and EN 301489-15

iii) Article 3.2

EN 301 783-2

iv)

Düsseldorf 10 Oct. 2002

Place and date of issue

Icom (Europe) GmbH

Himmelgeister straße 100

D-40225 Düsseldorf

Authorized representative name

T.Maebayashi General Manager

Signature

Page 79

Image 79

Icom IC-R5 instruction manual Declaration Conformity, We Icom Inc. Japan

Contents

IR5 Explicit Definitions Precaution Iii Supplied Accessories Table of Contents Belt clip Battery installationQuick Reference Guide Preparation Rotate Dial to select Y then push Band Install the Ni-Cd batteriesCharging conﬁrmation is displayed as below Your ﬁrst scanning Experience About default settingBasic operation Selecting a memory Channel Receive mode selectionSetting frequency Memory programming Selecting a scan edge channel B Programmed scan operationProgramming scan edges Selecting a scan edge channel a Starting scan Starting scan Select VFO modeCancelling scan Selecting a scanning type Front, top and side panels Panel Description UCONTROL Dial Dial Push for 1 sec. to turn the receiver power on and OFF TTONE Indicators WLOCK Indicator pERECEIVE Mode Indicator p RDUPLEX Indicators p 1SIGNAL Strength Indicator p Priority Watch Indicator p2VOLUME Exchange Indicator p Charging caution Battery ChargingBattery installation Battery caution Charging periods Approx hours Battery chargingCharging connections Charging description VFO and memory channels Frequency and Channel SettingOperating band selection Available frequency bands Frequency and Channel Setting Rotate Dial to select the desired frequency band Setting a frequencySetting a tuning step Tuning step selection Rotate Dial to select the desired memory channel Push V/MS.MW~ to select the memory modeSelecting a memory channel Lock function Receiving Setting audio volumeWhen a signal is received Basic Operation Receive mode selection Squelch level setting Attenuator function Monitor functionPush and hold SQL to monitor the operating frequency Duplex operation SettingRotate Dial to select DUP Push Tsset momentarily to exit set mode Setting dial select stepDial select step General description Memory Channels Rotate Dial to select the desired bank channel number Memory bank settingPush V/MS.MW~ momentarily to set the channel into the bank To return to regular memory condition, rotate Dial while Memory bank selectionPush V/MS.MW~ to select memory mode, if desired Rotate Dial to select the bank channel Rotate Dial to move the cursor to left or right Programming memory/bank nameAvailable characters Selecting bank channel indication Selecting display type Copying memory contents Essary Push V/MS.MW~ for 1 sec. to clear the contentsMemory clearing While pushing FUNC, push V/MS.MW~ for 1 sec Transferring memory contents Erasing/transferring bank contents FREQUENCY/MEMORY Skip Function p Scan OperationScan types Full Scan p Full/band/programmed scan Select VFO mode with V/MS.MW~To start the scan, push Modescan Example Programming 145.300 MHz into scan edges 03A Scan edges programming Memory/bank/all bank scan Select memory mode with V/MS.MW~ Clearing the stored frequencies Auto memory write scanDuring auto-memory write scanning Re-calling the stored frequencies Nel Skip channel/frequency setting Scan resume timer Scan pause timerScan resume condition Watch starts Priority WatchPriority watch types About priority beep function Select memory mode, or the desired bank group then Push Tsset to exit set mode and start the watchPush Tsset to cancel the watch Priority watch operation When scanning memory/bank channels VFO scan watch qSelect memory mode0Push Tsset to cancel the watch and scan Step y Tone Squelch and Pocket BeepTone/DTCS squelch operation OPush Func to stop the beeps and blinking manually Available Dtcs code list Tone squelch frequency/DTCS code settingAvailable tone frequency list Dtcs polarity setting While pushing FUNC, push Modescan to start the tone scan Tone scan General SET ModeSet mode entering and operation Expanded set mode ON/OFF General set mode items Set mode itemsExpanded set mode items Beep output level Dial select stepPriority watch Key-touch beep Antenna selection Power saveMHz differ according to version, re Dial speed acceleration Monitor switch actionNo accessible switch is available, except Key lock effect Scan stop beep Auto power OFFScan pause timer Scan resume timer Duplex direction Offset frequencyTone squelch Available Dtcs code DTone frequency Ddtcs codeDtcs polarity Available subaudible tone frequencies Weather alert function LCD contrastTurns weather alert function on and OFF Antenna selection Other FunctionsSelecting antenna Weather channel operation Dial function assignmentWeather channel selection Turn the weather alert function OFF in set mode Push SQL on the master receiver Cloning between receivers Cloning using a personal computer Auto power-off functionCloning error Partial reset Dccir channels Frequency TableTV channels DU.S.A. channels Channels DChina channelsDNew Zealand FOT channels Indonesian channelsDItalian channels Taiwan channels Weather channelsunit MHz VHF marine channels Murs channels Other communications in the USAHF CB Citizens Band channels General aviation frequencies Wireless MicrophonesDCable TV IRC Other communications- other countries LPD Low Power Device channels Unit MHzPMR446 channels unit MHz UHF C.R.S Citizen Radio Service channels Troubleshooting Maintenance CP-18A/E fuse replacement Dgeneral Specifications Options Options Pocket Guide Memory channel programming We Icom Inc. Japan Declaration Conformity Kamiminami, Hirano-ku, Osaka 547-0003 Japan