Icom IC-R5 Marine Radio Manual: Operation Guide and Features

66

q Cutw Fold e Complete

Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc.

<CUT HERE>

POCKET GUIDE 15

POCKET GUIDE

iR5

■VFO and memory mode selection

➥Push [V/M•S.MW•~] to toggle between VFO and memory mode.

■Receive mode selection

➥Push [MODE•SCAN] several times to select the desired mode

■Audio level setting

➥Push [Y] to increase, push [Z] to decrease the audio level.

■Squelch level setting

➥While pushing [SQL], rotate [DIAL] to set the squelch level.

■Frequency band selection

➥Push [BAND•] several times,

or while pushing [BAND• ], rotate [DIAL] to select the desired frequency band.

■Tuning step selection

➥Push [TS•SET], then rotate [DIAL] to select the desired tuning step.

•Push [TS•SET] again to return to the previous condition.

■Key lock function

➥While pushing [FUNC], push

[BAND•] for 1 sec. to toggle the key lock function ON and OFF.

•“ ” appears when the lock function is in use.

■Attenuator function

➥While pushing [FUNC], push [SQL] to toggle the attenuator ON and OFF.

•“ ” appears when the lock func- tion is in use.

■Frequency setting

qPush [V/M•S.MW•~] to select VFO mode.

wRotate [DIAL] to set the desired operating frequency.

■Memory channel selection

qPush [V/M•S.MW•~] to select memory mode.

wRotate [DIAL] to set the desired memory channel.

•While pushing [FUNC], [DIAL] rotation changes memory channel in 10 channels steps.

■Memory bank channel selection

qPush [V/M•S.MW•~] to select memory mode.

wPush [BAND•] several times,

or while pushing [BAND• ], rotate [DIAL] to select the desired bank.

eRotate [DIAL] to select the desired bank channel.

Image 77

Icom IC-R5 instruction manual Pocket Guide

Contents

IR5 Explicit Definitions Precaution Iii Supplied Accessories Table of Contents Quick Reference Guide Battery installationPreparation Belt clip Charging conﬁrmation is displayed as below Install the Ni-Cd batteriesRotate Dial to select Y then push Band Basic operation About default settingYour ﬁrst scanning Experience Setting frequency Receive mode selectionMemory programming Selecting a memory Channel Programming scan edges Programmed scan operationSelecting a scan edge channel a Selecting a scan edge channel B Cancelling scan Starting scan Select VFO modeSelecting a scanning type Starting scan Front, top and side panels Panel Description UCONTROL Dial Dial Push for 1 sec. to turn the receiver power on and OFF ERECEIVE Mode Indicator p WLOCK Indicator pRDUPLEX Indicators p TTONE Indicators 2VOLUME Exchange Indicator p Priority Watch Indicator p1SIGNAL Strength Indicator p Battery installation Battery ChargingBattery caution Charging caution Charging connections Battery chargingCharging description Charging periods Approx hours Operating band selection Frequency and Channel SettingVFO and memory channels Available frequency bands Frequency and Channel Setting Setting a tuning step Setting a frequencyTuning step selection Rotate Dial to select the desired frequency band Selecting a memory channel Push V/MS.MW~ to select the memory modeLock function Rotate Dial to select the desired memory channel When a signal is received Setting audio volumeBasic Operation Receiving Receive mode selection Squelch level setting Push and hold SQL to monitor the operating frequency Monitor functionAttenuator function Rotate Dial to select DUP SettingDuplex operation Dial select step Setting dial select stepPush Tsset momentarily to exit set mode General description Memory Channels Push V/MS.MW~ momentarily to set the channel into the bank Memory bank settingRotate Dial to select the desired bank channel number Push V/MS.MW~ to select memory mode, if desired Memory bank selectionRotate Dial to select the bank channel To return to regular memory condition, rotate Dial while Available characters Programming memory/bank nameRotate Dial to move the cursor to left or right Selecting bank channel indication Selecting display type Copying memory contents Memory clearing Push V/MS.MW~ for 1 sec. to clear the contentsWhile pushing FUNC, push V/MS.MW~ for 1 sec Essary Transferring memory contents Erasing/transferring bank contents Scan types Scan OperationFull Scan p FREQUENCY/MEMORY Skip Function p To start the scan, push Modescan Select VFO mode with V/MS.MW~Full/band/programmed scan Example Programming 145.300 MHz into scan edges 03A Scan edges programming Memory/bank/all bank scan Select memory mode with V/MS.MW~ During auto-memory write scanning Auto memory write scanRe-calling the stored frequencies Clearing the stored frequencies Nel Skip channel/frequency setting Scan resume condition Scan pause timerScan resume timer Priority watch types Priority WatchAbout priority beep function Watch starts Push Tsset to cancel the watch Push Tsset to exit set mode and start the watchPriority watch operation Select memory mode, or the desired bank group then 0Push Tsset to cancel the watch and scan VFO scan watch qSelect memory modeWhen scanning memory/bank channels Tone/DTCS squelch operation Tone Squelch and Pocket BeepOPush Func to stop the beeps and blinking manually Step y Available tone frequency list Tone squelch frequency/DTCS code settingAvailable Dtcs code list Dtcs polarity setting While pushing FUNC, push Modescan to start the tone scan Tone scan Set mode entering and operation SET ModeExpanded set mode ON/OFF General Expanded set mode items Set mode itemsGeneral set mode items Priority watch Dial select stepKey-touch beep Beep output level MHz differ according to version, re Power saveAntenna selection No accessible switch is available, except Monitor switch actionKey lock effect Dial speed acceleration Scan pause timer Auto power OFFScan resume timer Scan stop beep Tone squelch Offset frequencyDuplex direction Dtcs polarity DTone frequency Ddtcs codeAvailable subaudible tone frequencies Available Dtcs code Turns weather alert function on and OFF LCD contrastWeather alert function Selecting antenna Other FunctionsAntenna selection Weather channel selection Dial function assignmentWeather channel operation Turn the weather alert function OFF in set mode Push SQL on the master receiver Cloning between receivers Cloning error Auto power-off functionCloning using a personal computer Partial reset TV channels Frequency TableDU.S.A. channels Dccir channels DNew DChina channelsZealand Channels DItalian channels Indonesian channelsTaiwan channels FOT channels Weather channelsunit MHz VHF marine channels HF CB Citizens Band channels Other communications in the USAMurs channels DCable TV IRC Wireless MicrophonesGeneral aviation frequencies PMR446 channels unit MHz LPD Low Power Device channels Unit MHzOther communications- other countries UHF C.R.S Citizen Radio Service channels Troubleshooting Maintenance CP-18A/E fuse replacement Dgeneral Specifications Options Options Pocket Guide Memory channel programming We Icom Inc. Japan Declaration Conformity Kamiminami, Hirano-ku, Osaka 547-0003 Japan