Ryobi TS1300 warranty Adjustments, Dust BAG Optional

Page 14

ASSEMBLY

■Replace the lower blade guard and blade bolt cover.

■Retighten phillips screw securing blade bolt cover.

WARNING:

Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock button when blade is rotating.

DUST BAG (Optional)

An optional dust bag, part number 4090001, is available for use on your miter saw. It fits over the exhaust port on the upper blade guard. To install it, remove dust guide from exhaust port. Then, squeeze the two metal clips to open the mouth of the bag and slide it on the exhaust port. Release the clips. The metal ring in the bag should lock in between the grooves on the exhaust port.

To remove the dust bag for emptying, simply reverse the above procedure.

TABLE EXTENSIONS (Optional)

To install optional table extensions, part number 982022-001, insert the ends of extensions into the holes in the sides of the base. Adjust the extensions to the desired length. To secure them in place, screw the two thumb screws provided into the holes in the front of the base and tighten them securely.

WARNING:

Before connecting saw to power source, make sure the saw blade or blade guard will not hit the work clamp or table extensions when cutting 35° to 45° angles.

STOP BLOCK (Optional)

The optional stop block is included with the Table exten- sions and is useful as a stop for making repetitive cuts to the same length. It can be installed on either side of the saw base:

■Loosen the thumb screw and adjust the stop block the desired distance from the blade for the cut to be made. For accurate placement of the stop block, measure the distance from the teeth set on the blade to the stop block.

■Tighten thumb screw securely.

■Make a test cut in scrap material and measure the length of the workpiece.

■Make any necessary adjustments.

WARNING:

When using the work clamp with the stop block, install the clamp on the same side as the stop block. This will eliminate the possibility of trapping the workpiece, resulting in the saw blade and workpiece kicking up. Failure to heed this warning can result in serious personal injury.

WARNING:

Always make sure your miter saw is securely mounted to a workbench or an appropriate workstand. Failure to do so could result in an accident resulting in possible serious personal injury.

ADJUSTMENTS

Your Ryobi miter saw has been adjusted at the factory for making very accurate cuts. However, some of the compo- nents might have been jarred out of alignment during ship- ping. Also, over a period of time, readjustment will probably become necessary due to wear. After unpacking your saw, check the following adjustments before you begin using saw. Make any readjustments that are necessary and peri- odically check the parts alignment to make sure that your saw is cutting accurately.

WARNING:

Your saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. Discon- necting your saw will prevent accidental starting that could cause serious injury.

NOTE: Many of the illustrations in this manual show only portions of your miter saw. This is intentional so that we can clearly show points being made in the illustrations. Never operate your saw without all guards securely in place and in good operating condition.

Page 14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Save this Manual for Future Reference Thank YOU for Buying a Ryobi Miter SAWTable of Contents Double Insulation Symbol Meaning Safety Alert SymbolRules for Safe Operation Read ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Additional Rules For Safe Operation For Miter Saws Product Specifications Glossary of Terms for WoodworkingUnpacking and Checking Contents AMP Motor FeaturesKnow Your Miter SAW Cutting CapacitiesSpindle Lock Button Miter Lock HandleLOCK-OFF Lever Trigger LockElectrical Connection Optional AccessoriesMounting Holes Dust Guide AssemblyTo Install Blade Double D Flats Blade Adjustments Dust BAG OptionalBlade Slot Framing Square Squaring the Miter Table to the FenceFence Miter Table Blade SlotMm Socket Squaring the SAW Blade to the FenceBlade Miter Framing Square Head Screws Mounting Bracket MiterOperation Pivot Adjustments Travel Pivot AdjustmentDepth Stop Adjustments Depth StopStraight Crosscut Cutting with Your Miter SAWCrosscutting Workpiece Supports Support Long WorkpiecesLong Workpiece Right Wrong Wide Board Cutting Warped MaterialClamping Wide Workpieces ClampLubrication MaintenanceGeneral Extension CordsBrush CAP Brush Assembly Brush ReplacementProceed as follows when replacement is required Troubleshooting Problem Cause SolutionFigure a Figure a Parts List Key Part Number Description QuanFigure B Figure B Parts List Operators Manual 10 in mm Miter Saw Model TS1300 Ryobi Technologies INC

TS1300 specifications

The Ryobi TS1300 is a standout tool in the landscape of portable table saws, catering to both professionals and DIY enthusiasts alike. This compact saw has gained recognition for its impressive blend of performance, convenience, and versatility, making it a popular choice for various woodworking tasks.

One of the main features of the TS1300 is its powerful 15-amp motor, delivering a robust performance capable of handling tough materials. This motor allows the saw to achieve a no-load speed of up to 5,000 RPM, enabling smooth and precise cuts. The saw is designed to handle both rip cuts and cross cuts, making it ideal for a range of applications, from crafting complex furniture to simple home repairs.

In terms of cutting capacity, the Ryobi TS1300 offers an impressive maximum rip capacity of 30 inches, allowing users to work on larger panels effortlessly. Its adjustable blade height and angle further enhance the tool’s versatility, providing a cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees. This adaptability is essential for craftsmen working on intricate projects requiring various angles and depths.

Moreover, the TS1300 is equipped with an innovative onboard storage system that keeps the accessories organized and readily available. This feature is particularly beneficial for users who need to quickly access their tools while working on different tasks, boosting overall efficiency.

Safety is also a key consideration with the Ryobi TS1300. The saw includes a blade guard and anti-kickback pawls to help minimize the risk of accidents during operation. The built-in push stick enhances user safety by allowing for safe maneuvering of materials without the risk of hand injury.

The lightweight and portable design of the TS1300 makes it easy to transport, making it a great option for job sites and home projects. Its folding stand provides stability while allowing for quick setup and teardown, enhancing user convenience.

In summary, the Ryobi TS1300 combines power, precision, and portability in a user-friendly package. Its range of features, from the powerful motor to the safety enhancements and mobility, positions it as a reliable choice for those looking to tackle woodworking projects with confidence and ease. Whether for professional use or home improvement tasks, the TS1300 delivers the performance and functionality required to achieve high-quality results.
Top Page Image Contents