Ryobi TS1300 warranty Before Making a CUT, be Sure ALL Adjustments are Secure

Page 5

RULES FOR SAFE OPERATION

29.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.

30.DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

31.USE THE FENCE. Always use the fence when cutting.

32.SUPPORT LONG WORKPIECES. To minimize risk of blade pinching and kickback, always support long workpieces.

33.BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE.

34.USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or blade screws that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).

35.USE RECOMMENDED ACCESSORIES. The use of improper accessories may cause risk of injury.

36.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the blade is unintentionally contacted.

37.POLARIZED PLUGS. To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

38.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Do not leave tool until it comes to a complete stop.

39.AVOID CUTTING NAILS. Inspect for and remove all nails from lumber before cutting.

40.NEVER TOUCH BLADE or other moving parts during use.

41.NEVER START A TOOL WHEN THE BLADE IS IN CONTACT WITH THE WORKPIECE.

42.DO NOT OPERATE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

43.SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and it frees both hands to operate tool.

44.REPLACEMENT PARTS. All repairs, whether electrical or mechanical, should be made at your nearest Authorized Service Center.

WARNING:

When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.

45.SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct other users. If you loan someone this tool, loan them these instructions also.

WARNING:

WEAR YOUR

SAFETY GLASSES

FORESIGHT IS BETTER

THAN NO SIGHT

The operation of any saw can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Thank YOU for Buying a Ryobi Miter SAW Save this Manual for Future ReferenceTable of Contents Double Insulation Symbol Meaning Safety Alert SymbolRules for Safe Operation Read ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Additional Rules For Safe Operation For Miter Saws Glossary of Terms for Woodworking Product SpecificationsUnpacking and Checking Contents Know Your Miter SAW FeaturesAMP Motor Cutting CapacitiesLOCK-OFF Lever Miter Lock HandleSpindle Lock Button Trigger LockElectrical Connection Optional AccessoriesMounting Holes Dust Guide AssemblyTo Install Blade Double D Flats Blade Dust BAG Optional AdjustmentsFence Miter Table Squaring the Miter Table to the FenceBlade Slot Framing Square Blade SlotBlade Miter Framing Square Squaring the SAW Blade to the FenceMm Socket Head Screws Mounting Bracket MiterDepth Stop Adjustments Pivot Adjustments Travel Pivot AdjustmentOperation Depth StopStraight Crosscut Cutting with Your Miter SAWCrosscutting Workpiece Supports Support Long WorkpiecesLong Workpiece Clamping Wide Workpieces Cutting Warped MaterialRight Wrong Wide Board ClampGeneral MaintenanceLubrication Extension CordsBrush CAP Brush Assembly Brush ReplacementProceed as follows when replacement is required Problem Cause Solution TroubleshootingFigure a Key Part Number Description Quan Figure a Parts ListFigure B Figure B Parts List Ryobi Technologies INC Operators Manual 10 in mm Miter Saw Model TS1300

TS1300 specifications

The Ryobi TS1300 is a standout tool in the landscape of portable table saws, catering to both professionals and DIY enthusiasts alike. This compact saw has gained recognition for its impressive blend of performance, convenience, and versatility, making it a popular choice for various woodworking tasks.

One of the main features of the TS1300 is its powerful 15-amp motor, delivering a robust performance capable of handling tough materials. This motor allows the saw to achieve a no-load speed of up to 5,000 RPM, enabling smooth and precise cuts. The saw is designed to handle both rip cuts and cross cuts, making it ideal for a range of applications, from crafting complex furniture to simple home repairs.

In terms of cutting capacity, the Ryobi TS1300 offers an impressive maximum rip capacity of 30 inches, allowing users to work on larger panels effortlessly. Its adjustable blade height and angle further enhance the tool’s versatility, providing a cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees. This adaptability is essential for craftsmen working on intricate projects requiring various angles and depths.

Moreover, the TS1300 is equipped with an innovative onboard storage system that keeps the accessories organized and readily available. This feature is particularly beneficial for users who need to quickly access their tools while working on different tasks, boosting overall efficiency.

Safety is also a key consideration with the Ryobi TS1300. The saw includes a blade guard and anti-kickback pawls to help minimize the risk of accidents during operation. The built-in push stick enhances user safety by allowing for safe maneuvering of materials without the risk of hand injury.

The lightweight and portable design of the TS1300 makes it easy to transport, making it a great option for job sites and home projects. Its folding stand provides stability while allowing for quick setup and teardown, enhancing user convenience.

In summary, the Ryobi TS1300 combines power, precision, and portability in a user-friendly package. Its range of features, from the powerful motor to the safety enhancements and mobility, positions it as a reliable choice for those looking to tackle woodworking projects with confidence and ease. Whether for professional use or home improvement tasks, the TS1300 delivers the performance and functionality required to achieve high-quality results.
Top Page Image Contents