Bostitch manual N80CB Driver Maintenance Instructions, Directional Exhaust Deflector

Page 11

N80CB DRIVER MAINTENANCE INSTRUCTIONS

Worn driver causing poor quality or loss of power:

Wear on the driving tip will affect the nail drive, giving symptoms of bent and incompletely driven nails, and damaged nail heads.

The driver length may be adjusted to allow the driving tip to be redressed to compensate for wear. Heat and precise measurement are required. Contact a qualified service technician for this adjustment.

The length setting for a new driver is shown below. Measurement is from the bottom face of the main piston.

Note that the measurement from the top of the piston gives the maximum amount the driver may be adjusted to allow redressing. Always extend the driver the minimum required to allow redressing to restore the driving end; several redressings will be possible before this maximum depth is reached.

6.006.000"” - 6.60.020”"

Standard Length N80CB/N80P

Standard Length 80CB/N80P (152.4mm – 152.9mm)

(152.4mm - 152.9mm)

 

 

 

 

 

SEE NOTE

3/8" (9.5mm) maximum limit of driver recessed

NOTE: WHEN DRESSING IS REQUIRED, USE

into piston. Do not exceed this limit

.015" - .025 x 45˚ CHAMFER

 

 

 

 

 

(.38 - .64mm x 45˚ CHAMFER)

NOTE: Driver wear of approximately 1/8” (3mm) can be tolerated in most applications. However, in difficult driving applications, driver wear or approximately 1/16” (1.5mm) may cause a slight reduction in the apparent driving power.

NOTE: For “Flush-Driving”, length settings shorter than shown above may be used. However, the adjusted length should never be less than 5.705” (144.9mm), or more than 6.055” (153.8mm), otherwise normal nailer function may be adversely affected.

DIRECTIONAL EXHAUST DEFLECTOR

Loosen screw as shown. Adjust to desired exhaust direction and tighten screw.

 

 

ACCESSORIES AVAILABLE:

BC601

4 oz. Bostitch Air-Tool Lubricant

 

BC602

1 pint Bostitch Air-Tool Lubricant

 

BC603

1 pint Bostitch “Winter-Formula” Air-Tool Lubricant

BC604

1 quart Bostitch Air-Tool Lubricant

 

100679

Lube 1 lb. can

 

SEQ5

Sequential Trip Conversion Kit

 

N80K2

Remote Control Kit

 

N80CK1

Smooth Trip Kit

 

N80CK2

Dial-A-DepthTMFastener Control Kit

 

ORK11

O-Ring Kit

 

BK3

Bumper Kit

 

N80154A

Replacement Driver Assembly - A “Hard Driver” for high volume applications, such as pallets

851325

Loctite 271 (.02 oz.)

 

831385

Loctite 242 (.02 oz.)

 

105005

Assembly, Adjustable Contact Trip

 

CNTK2

Contact Trip Conversion Kit (Black Trigger)

TVA6

Trigger Valve Assembly

-11-

 

 

Image 11
Contents N80CB Index IntroductionOperation Safety InstructionsAIR Supply and Connections Loading ToolN80CB Tool Specifications Lubrication Load the coil of nails N80CB accepts from 1-1/2 to 3-1/4 nails To change settingLoading the N80CB Series Coil Nailer To Prevent Accidental InjuriesSequential Trip Operation Tool OperationBefore Handling or Operating this Tool Contact Trip OperationBOSTITCH, INC Tool Operation CheckTool Must not Cycle Tool Must CycleMaintaining the Pneumatic Tool Replacement PartsAssembly Procedure for Seals AIR SUPPLY-PRESSURE and VolumeProblem TroubleshootingDirectional Exhaust Deflector N80CB Driver Maintenance InstructionsAccessories Available Nota IntroducciónÍndice Operación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaEspecificaciones DE LA Herramienta N80CB Lubricación Gire y cierre la tapa del cargador Cierre la puerta Advertencia Para Impedir Lesiones AccidentalesCargue un rollo de clavos Operación DE Disparo Secuencial Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disparo POR ContactoLA Herramienta SÍ Debe Efectuar SU Ciclo Operación POR Disparo SecuencialLA Herramienta no Debe Efectuar SU Ciclo Procedimiento DE Ensamble Para LOS Sellos Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Partes DE ReemplazoDiagnóstico DE Falla Accesorios Disponibles Deflector DE Escape DireccionalRemarque SommaireFonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DE L’APPAREIL N80CBLubrification Basculer le couvercle pour le fermer Fermer la porte Chargement DU Cloueur DE LA Série N80CBPour Prévenir UN Accident Introduire le rouleau de clousDéclenchement À LA Volée Mode D’EMPLOIFonctionnement DE L’APPAREIL Avant DE Manipuler OU D’UTILISER CET Outil’APPAREIL NE Doit PAS SE Déclencher Vérification DU Système DE DéclenchementSystème DE Sécurité À LA Volée Système DE Sécurité AU COUP-PAR-COUPProcédure D’ASSEMBLAGE DES Garnitures Alimentation D’AIR Pression VolumePièces DE Rechange Cause Problèmes DE FonctionnementDéflecteur D’ÉCHAPPEMENT Directionnel Accessoires Disponibles