Bostitch N80CB Maintaining the Pneumatic Tool, Replacement Parts, Assembly Procedure for Seals

Page 9

MAINTAINING THE PNEUMATIC TOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

REPLACEMENT PARTS:

BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, swivel fittings, low points containing water and anything else that would prevent full volume flow of air to the tool.

-9-

Image 9

Contents N80CB Index IntroductionAIR Supply and Connections Safety InstructionsLoading Tool OperationN80CB Tool Specifications Lubrication Loading the N80CB Series Coil Nailer N80CB accepts from 1-1/2 to 3-1/4 nails To change settingTo Prevent Accidental Injuries Load the coil of nailsBefore Handling or Operating this Tool Tool OperationContact Trip Operation Sequential Trip OperationTool Must not Cycle Tool Operation CheckTool Must Cycle BOSTITCH, INCAssembly Procedure for Seals Replacement PartsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolProblem TroubleshootingN80CB Driver Maintenance Instructions Accessories AvailableDirectional Exhaust Deflector Introducción ÍndiceNota Suministro DE Aire Y Conexiones Instrucciones DE SeguridadAL Cargar LA Herramienta OperaciónEspecificaciones DE LA Herramienta N80CB Lubricación Advertencia Para Impedir Lesiones Accidentales Cargue un rollo de clavosGire y cierre la tapa del cargador Cierre la puerta Antes DE Manejar U Operar Esta Herramienta Operación DE LA HerramientaOperación DE Disparo POR Contacto Operación DE Disparo SecuencialOperación POR Disparo Secuencial LA Herramienta no Debe Efectuar SU CicloLA Herramienta SÍ Debe Efectuar SU Ciclo Mantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AirePartes DE Reemplazo Procedimiento DE Ensamble Para LOS SellosDiagnóstico DE Falla Accesorios Disponibles Deflector DE Escape DireccionalRemarque SommaireAlimentation EN AIR Comprimé ET Raccordement Consignes DE SécuritéChargement DE L’APPAREIL FonctionnementOpération Caractéristiques DE L’APPAREIL N80CBLubrification Pour Prévenir UN Accident Chargement DU Cloueur DE LA Série N80CBIntroduire le rouleau de clous Basculer le couvercle pour le fermer Fermer la porteFonctionnement DE L’APPAREIL Mode D’EMPLOIAvant DE Manipuler OU D’UTILISER CET Outil Déclenchement À LA VoléeSystème DE Sécurité À LA Volée Vérification DU Système DE DéclenchementSystème DE Sécurité AU COUP-PAR-COUP ’APPAREIL NE Doit PAS SE DéclencherAlimentation D’AIR Pression Volume Pièces DE RechangeProcédure D’ASSEMBLAGE DES Garnitures Cause Problèmes DE FonctionnementDéflecteur D’ÉCHAPPEMENT Directionnel Accessoires Disponibles