Bostitch N80CB manual Lubrication

Page 5

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

FITTINGS:

Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source.

HOSES:

Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system. The supply hose should contain a fitting that will provide “quick disconnecting” from the male plug on the tool.

SUPPLY SOURCE:

Use only clean regulated compressed air as a power source for this tool. NEVER USE OXYGEN, COMBUSTIBLE GASES, OR BOTTLED GASES, AS A POWER SOURCE FOR THIS TOOL AS TOOL MAY EXPLODE.

REGULATOR:

A pressure regulator with an operating pressure of 0 - 125 p.s.i. (0 - 8.79 kg/cm2) is required to control the operat ing pressure for safe operation of this tool. Do not connect this tool to air pressure which can potentially exceed 200 p.s.i. (14 kg/cm2) as tool may fracture or burst, possibly causing injury.

OPERATING PRESSURE:

Do not exceed recommended maximum operating pressure as tool wear will be greatly increased. The air supply must be capable of maintaining the operating pressure at the tool. Pressure drops in the air supply can reduce the tool’s driving power. Refer to “TOOL SPECIFICATIONS” for setting the correct operating pressure for the tool.

FILTER:

Dirt and water in the air supply are major causes of wear in pneumatic tools. A filter will help to get the best performance and minimum wear from the tool. The filter must have adequate flow capacity for the specific installation. The filter has to be kept clean to be effective in providing clean compressed air to the tool. Consult the manufacturer’s instructions on proper maintenance of your filter. A dirty and clogged filter will cause a pressure drop which will reduce the tool’s performance.

LUBRICATION

Frequent, but not excessive, lubrication is required for best performance. Oil added through the air line connection will lubricate the internal parts. Use BOSTITCH Air Tool Lubricant, Mobil Velocite #10, or equivalent. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance.

If no airline lubricator is used, add oil during use into the air fitting on the tool once or twice a day. Only a few drops of oil at a time is necessary. Too much oil will only collect inside the tool and will be noticeable in the exhaust cycle.

COLD WEATHER OPERATION:

For cold weather operation, near and below freezing, the moisture in the air line may freeze and prevent tool operation. We recommend the use of BOSTITCH WINTER FORMULA air tool lubricant or permanent antifreeze (ethylene glycol) as a cold weather lubricant.

CAUTION: Do not store tools in a cold weather environment to prevent frost or ice formation on the tools operating valves and mechanisms that could cause tool failure.

NOTE:Some commercial air line drying liquids are harmful to “O”-rings and seals – do not use these low temperature air dryers without checking compatibility.

-5-

Image 5
Contents N80CB Index IntroductionAIR Supply and Connections Safety InstructionsLoading Tool OperationN80CB Tool Specifications Lubrication Loading the N80CB Series Coil Nailer N80CB accepts from 1-1/2 to 3-1/4 nails To change settingTo Prevent Accidental Injuries Load the coil of nailsBefore Handling or Operating this Tool Tool OperationContact Trip Operation Sequential Trip OperationTool Must not Cycle Tool Operation CheckTool Must Cycle BOSTITCH, INCAssembly Procedure for Seals Replacement PartsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolProblem TroubleshootingDirectional Exhaust Deflector N80CB Driver Maintenance InstructionsAccessories Available Nota IntroducciónÍndice Suministro DE Aire Y Conexiones Instrucciones DE SeguridadAL Cargar LA Herramienta OperaciónEspecificaciones DE LA Herramienta N80CB Lubricación Gire y cierre la tapa del cargador Cierre la puerta Advertencia Para Impedir Lesiones AccidentalesCargue un rollo de clavos Antes DE Manejar U Operar Esta Herramienta Operación DE LA HerramientaOperación DE Disparo POR Contacto Operación DE Disparo SecuencialLA Herramienta SÍ Debe Efectuar SU Ciclo Operación POR Disparo SecuencialLA Herramienta no Debe Efectuar SU Ciclo Mantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AirePartes DE Reemplazo Procedimiento DE Ensamble Para LOS SellosDiagnóstico DE Falla Accesorios Disponibles Deflector DE Escape DireccionalRemarque SommaireAlimentation EN AIR Comprimé ET Raccordement Consignes DE SécuritéChargement DE L’APPAREIL FonctionnementOpération Caractéristiques DE L’APPAREIL N80CBLubrification Pour Prévenir UN Accident Chargement DU Cloueur DE LA Série N80CBIntroduire le rouleau de clous Basculer le couvercle pour le fermer Fermer la porteFonctionnement DE L’APPAREIL Mode D’EMPLOIAvant DE Manipuler OU D’UTILISER CET Outil Déclenchement À LA VoléeSystème DE Sécurité À LA Volée Vérification DU Système DE DéclenchementSystème DE Sécurité AU COUP-PAR-COUP ’APPAREIL NE Doit PAS SE DéclencherProcédure D’ASSEMBLAGE DES Garnitures Alimentation D’AIR Pression VolumePièces DE Rechange Cause Problèmes DE FonctionnementDéflecteur D’ÉCHAPPEMENT Directionnel Accessoires Disponibles