Garmin 225B, 225A manual Load Database function. Then, press the ENT key

Page 33

3.4.5Load Database

The GTR 225 has a USB connector to allow for easily updating the system databases.

NOTE: Garmin recommends the use of a USB 2.0 compatible USB flash drive for updating the database.

1.Insert the supplied cable into the USB port on the top right corner of the GTR 225.

2.Insert the USB memory device into the other end of the cable.

USB Port

USB Cable

USB Memory Device

Figure 3-25 USB Update Progress

3.Press FUNC to access the Functions. Turn the LARGE knob to select the SYS Function. Turn the SMALL knob to view the

Load Database function. Then, press the ENT key.

Figure 3-38 Database Update Display

4.Verify the database version on USB. Then, press the ENT key. Updating will begin automatically.

Figure 3-39 Verify Database Version

190-01182-00 Rev. A

Garmin GTR 225/225A/225B Pilot’s Guide

3-15

Image 33

Contents GTR 225/225A/225B November Limited Warranty Garmin GTR 225/225A/225B Pilot’s Guide Operation US Toll Free Canada Toll Free Product Registration and SupportContents Index Index-1 Photo Sensor Product DescriptionPilot Controls Power/Com Volume/Squelch KnobFLIP/FLOP Key Tuning LARGE/SMALL Concentric Cursor KnobsCom Key MEM KeyUSB Port Func Function KeyMON Monitor Key Com Radio Power OnSelecting a Com Frequency Selected FrequencySaving a Com Channel Monitoring the Standby Com ChannelAfter selecting the desired characters, press ENT Monitor Annunciation Standby Frequency Being MonitoredSelected Wpt Type After making a selection, press ENTCom Database Look-Up Emergency ChannelActive and Standby frequencies Frequency Database Reverse Look-Up Stuck MicRemote Frequency Selection Control Airport Identifier Shown For Freqs In DatabaseThis page intentionally left blank Functions Description SYS Config Com SpacingPress the Func key to access the Functions Com FrequenciesRecent Com Frequencies Press the CLR key to delete this User frequency Com User FrequenciesSelected Frequency Select Wpt Name Select Wpt Type Press ENT Key To Delete Selected FreqSelect User Freqs Frequencies. Press ENTSelect User Freq Value Select User Wpt NamePress ENT Key To Set Selected Freq As Standby Com Database FrequenciesIdentifier Selected Freq As ActiveCom Nearest Area Control Center ACC Frequencies Com Nearest Airports APTTurn the Small knob to display the available ACCs Turn Small Knob To Scroll Through Available Airports13 Com Nearest FSS Frequencies Com Nearest Flight Service Station FSS Frequencies14 Com Nearest Weather Frequencies Com Nearest Weather WX FrequenciesAdjust Intercom ICS ConfigurationTurn the Small knob to turn the Aux Audio On or Off Aux AudioSpeaker On/Off Intercom On/OffIntercom On/Off function. Then, press the ENT key Speaker On/Off function. Then, press ENTSystem Configuration Com SpacingTurn the Small Knob to Select the Channel Spacing Display Brightness BrightnessSelect the Offset Value Database Info Display ContrastDisplay Contrast function. Then, press the ENT key Database Version function. Then, press the ENT keyLoad Database Load Database function. Then, press the ENT keyUSB Port USB Cable USB Memory Device Serial Number Software VersionPress the Func key to return to the main menu Serial Number function. Then, press ENTSetting Up the Count Down Timer TimersViewing Timers in the Com Display Setting Up the Count Up TimerPressing CLR and then ENT will reset the displayed Timer Pressing ENT twice will stop the displayed Timer36 Count Down Timer Value Now Counting Up Count Down Timer Value Highlighted When Counting UpThis page intentionally left blank Appendix TroubleshootingOr disabled via a Remote mounted It can be enabledIf in Lock Out mode Check Mic key inputUpdating the Frequency Database Messages Switch has been Power has been Re-apply power to the unitAll installations Radio will no longer TransmitThis input will now InstallationsIndex Stuck mic 2-5 Support