Hobart Welding Products 1025 manual 115V, Installing Alternative Plug

Page 19

3-8. Setting Input Voltage Selector Switch And Connecting Input Power

115V 230V

S-176 481-A

2

14

Rear Of Unit

3

Check input voltage available at site.

1 Input Voltage Selector Switch

Switch is accessible through slot in rear panel.

2 Changeover Switch Label

Look at label to find correct switch position.

Move switch to match input voltage.

3 Supplied 115 VAC Plug

If plug does not match voltage at re- ceptacle or type of receptacle, install suitable plug according to Section 3-9.

YBe sure input power connec- tion meets all applicable na- tional, regional, and local electrical codes.

4115 Or 230 VAC Receptacle

(115 VAC Shown)

YTo use rated output (see specifications), connect the unit to an individual branch circuit capable of carrying the effective (eff) current for the output being used. The unit must have a properly sized plug installed and the circuit must be protected by proper- ly sized fuses or circuit break- ers.

Connect plug to proper receptacle. Be sure receptacle can handle load.

Tools Needed:

ST-801 304-B / ST-801 319-B

3-9. Installing Alternative Plug

This procedure is necessary if the unit is to be connected to a 230 VAC receptacle, or to a 115 VAC receptacle that requires a plug that is different from the supplied plug.

See Section 3-8for instructions on setting input voltage selector switch for proper voltage.

2

3

6

1 7

4

5

1 Supplied 115 VAC Plug

Cut cord close to plug.

2Alternative PLug (230 VAC Plug Shown)

3Load 1 (Brass) Terminal

4Load 2 (Brass) Terminal

5Ground (Green) Terminal

6Outer Shell

7Cord Grip

Strip cord jacket back enough to separate conductors. Strip conduc- tors enough to make good contact with plug terminals. Make plug con- nections and reinstall outer shell and cord grip. Tighten assembly screws onto shell. Do not overtighten.

Tools Needed:

Ref. ST-801 305-A / ST-801 611

OM-2210 Page 15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Processes OM-2210Description Page Table of Contents Standards DirectivesCutting can cause fire or explosion Symbol UsageMarks a special safety message Plasma Arc Cutting HazardsFumes and Gases can be hazardous Flying Sparks can cause injuryARC Rays can burn eyes and skin Noise can damage hearingPrincipal Safety Standards About Pacemakers EMF InformationIdentifie un message de sécurité particulier Signification des symbolesLE Coupage présente un risque de feu ou d’explosion UNE Décharge Électrique peu t entraîner la mortLES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresPrincipales normes de sécurité Consignes relatives aux stimulateurs cardiaques Information sur les champs électromagnétiques− Definitions I1eff Symbols And DefinitionsManufacturer’s Rating Label For CE Products I1maxSpecifications For CE Model − InstallationOverheating Exceeding duty cycle can damage unit and void warrantyDuty Cycle And Overheating For Non-CE Model Duty Cycle And Overheating For CE ModelMovement Do not move or operate unit Dimensions And WeightWhere it could tip Selecting a LocationPressure Connecting Work Clamp And Gas/Air Supply115V Installing Alternative Plug− Operation Setting Gas/Air PressureControls Cutting Speed Example Of Cutting Operation Sequence Of OperationTrigger is pressed Every Week − Maintenance & TroubleshootingRoutine Maintenance Each UseChecking Torch Shield Cup Shutdown System Ways turn Off power when changing or checking consumablesTorch Connections Torch And Work Cable ConnectionsWork Cable Connections Trouble Remedy TroubleshootingCircuit Diagram For Power Source − Electrical DiagramMain Assembly − Parts ListDia Part Mkgs Description Quantity +181 Call Effective January 1Owner’s Record

1025 specifications

Hobart Welding Products has long been a trusted name in the welding industry, and their Hobart 1025 model stands out as a reliable choice for both professionals and hobbyists. Designed primarily for MIG welding, the Hobart 1025 is suitable for a variety of applications including automotive repairs, metal fabrication, and home projects.

One of the key features of the Hobart 1025 is its user-friendly interface. The machine comes equipped with an intuitive control panel that allows users to set their welding specifications easily, ensuring an efficient setup process. This is particularly beneficial for beginners who may find complex machines daunting. With its solid construction and portability, the Hobart 1025 can be used in various environments, making it a versatile tool for different welding tasks.

The welding output range of the Hobart 1025 is one of its standout characteristics. It offers a power range of 25 to 140 amps, allowing it to handle a wide range of materials from thin sheet metal to heavier stock. This flexibility enables welders to adjust the machine based on specific project requirements, delivering quality results each time. Additionally, the machine works well with a variety of wire types, including flux-cored and solid wire, providing users with more options for their welding needs.

Another highlight of the Hobart 1025 is its advanced technology. The machine features a built-in thermal overload protection mechanism that prevents overheating, thus prolonging its lifespan and ensuring safe operation. This technological aspect ensures that users can work longer without the risk of damaging the equipment.

Moreover, the Hobart 1025 is designed for efficiency. It boasts a smooth arc transfer that reduces spatter and produces clean welds, which minimizes the need for post-weld cleanup. This efficiency translates to time saved on projects, allowing users to focus on completing their work rather than dealing with excess cleanup.

In summary, the Hobart Welding Products 1025 model offers impressive features, flexibility, and advanced technologies that cater to a diverse range of welding applications. With its user-friendly design, reliable performance, and durable construction, it continues to be an exceptional choice for both novice and experienced welders alike.
Top Page Image Contents