Hobart Welding Products 1025 manual Effective January 1, Call

Page 31

Hobart Warranty

Effective January 1, 1997

Warranty Questions?

Call

1-800-332-6619.

This limited warranty supersedes all previous manufacturers warranties and is exclusive with no other guarantees or warranties expressed or implied.

LIMITED WARRANTY − Subject to the terms and conditions below, warrants to its original retail purchaser that new equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped from factory. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

Within the warranty periods listed below, manufacturer will repair or replace any warranted parts or components that fail due to such defects in material or workmanship. Manufacturer must be notified in writing within thirty (30) days of such defect or failure, at which time manufacturer will provide instructions on the warranty claim procedures to be followed.

Manufacturer shall honor warranty claims on warranted equipment listed below in the event of such a failure within the warranty time periods. All warranty time periods start on the date that the equipment was delivered to the original retail purchaser, or one year after the equipment is sent to the distributor.

1.5 Years Parts − 3 Years Labor

*Original main power rectifiers

2.3 Years — Parts and Labor

*Transformer/Rectifier Power Sources

*Plasma Arc Cutting Power Sources

*Semi-Automatic and Automatic Wire Feeders

*Robots

*Engine Driven Welding Generators

(NOTE: Engines are warranted separately by the engine manufacturer.)

3.1 Year — Parts and Labor

*Motor Driven Guns

*Process Controllers

*Water Coolant Systems

*HF Units

*Grids

*Spot Welders

*Load Banks

*SDX Transformers

*Running Gear/Trailers

*Field Options

(NOTE: Field options are covered under the limited warranty for the remaining warranty period of the product they are installed in, or for a minimum of one year — whichever is greater.)

4.6 Months — Batteries

5.90 Days — Parts and Labor

*MIG Guns/TIG Torches

*Plasma Cutting Torches

*Remote Controls

*Accessory Kits

*Replacement Parts

Limited Warranty shall not apply to:

1.Items furnished by manufacturer, but manufactured by others, such as engines or trade accessories. These items are covered by the manufacturer’s warranty, if any.

2.Consumable components; such as contact tips, cutting nozzles, contactors, relays, brushes, slip rings, or parts that fail due to normal wear.

3.Equipment that has been modified by any party other than manufacturer, or equipment that has been improperly installed, improperly operated or misused based upon industry standards, or equipment which has not had reasonable and necessary maintenance, or equipment which has been used for operation outside of the specifications for the equipment.

MANUFACTURER’S PRODUCTS ARE INTENDED FOR PURCHASE AND USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS TRAINED AND EXPERIENCED IN THE USE AND MAINTENANCE OF WELDING EQUIPMENT.

In the event of a warranty claim covered by this warranty, the exclusive remedies shall be, at manufacturers option: (1) repair; or (2) replacement; or, where authorized in writing by manufacturer in appropriate cases, (3) the reasonable cost of repair or replacement at an authorized service station; or

(4)payment of or credit for the purchase price (less reasonable depreciation based upon actual use) upon return of the goods at customer’s risk and expense. manufacturer’s option of repair or replacement will be F.O.B., Factory at Appleton, Wisconsin, or F.O.B. at an authorized service facility as determined by manufacturer. Therefore no compensation or reimbursement for transportation costs of any kind will be allowed.

TO THE EXTENT PERMITTED BY LAW, THE REMEDIES PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY.

ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT FURNISHED BY MANUFACTURER IS EXCLUDED AND DISCLAIMED BY MANUFACTURER.

Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion of incidental, indirect, special or consequential damages, so the above limitation or exclusion may not apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary from state to state.

In Canada, legislation in some provinces provides for certain additional warranties or remedies other than as stated herein, and to the extent that they may not be waived, the limitations and exclusions set out above may not apply. This Limited Warranty provides specific legal rights, and other rights may be available, but may vary from province to province.

hobart_warr 3/97

Image 31
Contents Processes OM-2210Description Page Table of Contents Standards DirectivesCutting can cause fire or explosion Symbol UsageMarks a special safety message Plasma Arc Cutting HazardsFumes and Gases can be hazardous Flying Sparks can cause injuryARC Rays can burn eyes and skin Noise can damage hearingPrincipal Safety Standards About Pacemakers EMF InformationIdentifie un message de sécurité particulier Signification des symbolesLE Coupage présente un risque de feu ou d’explosion UNE Décharge Électrique peu t entraîner la mortLES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresPrincipales normes de sécurité Consignes relatives aux stimulateurs cardiaques Information sur les champs électromagnétiques− Definitions I1eff Symbols And DefinitionsManufacturer’s Rating Label For CE Products I1maxSpecifications For CE Model − InstallationOverheating Exceeding duty cycle can damage unit and void warrantyDuty Cycle And Overheating For Non-CE Model Duty Cycle And Overheating For CE ModelMovement Do not move or operate unit Dimensions And WeightWhere it could tip Selecting a LocationPressure Connecting Work Clamp And Gas/Air Supply115V Installing Alternative Plug− Operation Setting Gas/Air PressureControls Cutting Speed Example Of Cutting Operation Sequence Of OperationTrigger is pressed Every Week − Maintenance & TroubleshootingRoutine Maintenance Each UseChecking Torch Shield Cup Shutdown System Ways turn Off power when changing or checking consumablesTorch Connections Torch And Work Cable ConnectionsWork Cable Connections Trouble Remedy TroubleshootingCircuit Diagram For Power Source − Electrical DiagramMain Assembly − Parts ListDia Part Mkgs Description Quantity +181 Call Effective January 1Owner’s Record

1025 specifications

Hobart Welding Products has long been a trusted name in the welding industry, and their Hobart 1025 model stands out as a reliable choice for both professionals and hobbyists. Designed primarily for MIG welding, the Hobart 1025 is suitable for a variety of applications including automotive repairs, metal fabrication, and home projects.

One of the key features of the Hobart 1025 is its user-friendly interface. The machine comes equipped with an intuitive control panel that allows users to set their welding specifications easily, ensuring an efficient setup process. This is particularly beneficial for beginners who may find complex machines daunting. With its solid construction and portability, the Hobart 1025 can be used in various environments, making it a versatile tool for different welding tasks.

The welding output range of the Hobart 1025 is one of its standout characteristics. It offers a power range of 25 to 140 amps, allowing it to handle a wide range of materials from thin sheet metal to heavier stock. This flexibility enables welders to adjust the machine based on specific project requirements, delivering quality results each time. Additionally, the machine works well with a variety of wire types, including flux-cored and solid wire, providing users with more options for their welding needs.

Another highlight of the Hobart 1025 is its advanced technology. The machine features a built-in thermal overload protection mechanism that prevents overheating, thus prolonging its lifespan and ensuring safe operation. This technological aspect ensures that users can work longer without the risk of damaging the equipment.

Moreover, the Hobart 1025 is designed for efficiency. It boasts a smooth arc transfer that reduces spatter and produces clean welds, which minimizes the need for post-weld cleanup. This efficiency translates to time saved on projects, allowing users to focus on completing their work rather than dealing with excess cleanup.

In summary, the Hobart Welding Products 1025 model offers impressive features, flexibility, and advanced technologies that cater to a diverse range of welding applications. With its user-friendly design, reliable performance, and durable construction, it continues to be an exceptional choice for both novice and experienced welders alike.